A peak of the wear rate under certain velocity was found.
发现在一定滑动速度下磨损率有一峰值。
Current has obviously affected on wear rate compared with loading.
在试验范围内，电流比载荷对磨损率的影响显著。
The calcium sulfonate additive reduces the wear rate of the materials.
基础油中磺酸钙的加入使氮化硅的磨损速率得到降低。
When thickness increases above a certain value, wear rate becomes unchanged.
但厚度增加到一定值时，磨损速率不变。
The results show that the wear rate increases with the increasing of load and wear speed;
结果表明：材料的磨损率随载荷的增加和磨损速度的增大而逐渐增大；
While giving other parameters, wear rate increases along with the increase of contact area.
当其余各影响参数保持一定值时，磨损率随接触面积的增大而增大。
The specific wear rate is strongly dependent on the temperature, atmosphere and contact pressure.
比磨损率也与温度、气氛和接触压力密切相关。
It can be applied in neural network measurement for the instantaneous wear rate of cutting tools.
可作为刀具瞬时磨损率神经网络测量的端系统。
There is an optimum surface roughness which will produce minimal arc energy and minimal wear rate.
表面粗糙度有一个最佳值，在这个表面粗糙度下电弧能量最小、质量磨损率也最小。
The wear rate of the end face of soft ring of B104a -70 mechanical seal was calculated and analyzed.
对B104 a - 70型机械密封软质环端面的磨损率进行了计算和分析。
It was proved by experiment that this testing method could give the change rule of wear rate on line.
实验结果表明：该检测方法完全可以满足磨损量变化趋势在线检测的要求。
The wear rate of graphite increases with the load, and the wear rate of IG11 is lower than that of MG.
石墨的磨损速率随载荷增加而增大，石墨ig11的耐磨性优于MG的。
Both toilet bars provide substantial lather, mild cleansing, low mush and wear rate levels during use.
两种盥洗用皂条都提供了丰富的泡沫、温和的清洁性、在使用过程中低的糊状物和磨损率水平。
The wear rate of rail steel increases linearly with the hardness of the corresponding wheel steel rising.
钢轨材料的磨损率随对应车轮硬度的增加而增加，且近似呈线性关系。
By investigating the relations of hardness difference to wear rate, the best friction pair mate was ascertained.
研究了配副硬度差与磨损率的关系，根据这种关系确定了最佳配副组合。
The results show that the friction coefficient and wear rate decrease with the increase of the graphite content.
研究表明，随著石墨含量的增加，摩擦系数和磨损量减小。
The wear rate of EMP increased with increasing of velocity and load at different rates under various test conditions.
EMP磨损率随滑动速度和载荷的升高耐增加，但不同试验条件的增幅不同；
The wear rate of EMP increases with the increase of velocity and load at a different pace under various test conditions.
弹性金属塑料材料的磨损率随滑动速度和载荷的升高而增加。
The negative oil film resistance is also found in the running-in, which results from the wear rate difference of the pair.
磨合试验中还发现了因齿面副两表面磨损率差形成的负电阻现象。
The results indicate that the wear ratio increases with the increase of the wear load and grit size, but the wear rate has less effect.
结果表明：磨损率随载荷和磨粒粒径的增大而增加，但磨损速度对磨损率的影响甚小。
The wear rate of composites decreases firstly and increases subsequently with the increase of the content of high carbon chromium iron.
随渗剂中高碳铬铁含量的增加，表面复合材料的磨损率先减少后增加；
The effects of metal base content and NiCr alloy addition on hardness, friction coefficient and wear rate of the composites were studied.
研究了金属基体及其中镍铬合金的含量对复合材料的硬度、摩擦系数和磨损率的影响。
Test results show that the developed brake composites have fairly stable friction coefficient, good fading resistance, low wear rate and...
对比试验表明，所研制的制动材料摩擦系数稳定，抗衰退性能好，磨损率较小，具有较大的性能价格比优势。
Moreover, the coatings with comparative lower abrasive wear rate can be deposited in the condition of moderate flows of oxygen and propane.
氧气流量、燃气流量适中的条件下制备的涂层磨损率较低。
The impacting force between tube and support plate is one of the parameters which plays a vital role in the prediction of tube fretting wear rate.
影响管子磨损的因素很多，关键参数之一是管子一支承板间的碰撞力。
The relative wear rate of compacted graphite cast iron cylinder liner is 63%, as compared with a grey cast iron cylinder liner of the same B content.
蠕墨铸铁硼缸套铸件与灰铸铁硼缸套相比，蠕墨铸铁缸套的相对磨损率为它的63%。
Wear and tear tests of the treated specimen are made by Brinell wear test machine, and the relation between wear rate and mechanical property is set up.
以上处理的试样经磨损试验，得到了磨损率和机械性能的一些关系。
With increasing of the holding time at high temperature, wear rate decreasing of low C-hi cr cast iron became more obvious, and wear resistance increased.
随着高温保温时间的延长，低碳高铬铸铁的磨损率降低幅度较大，耐磨性能提高。
Monte Carlo method was applied for simulating plastic deformation wear rate of materials under the three body abrasion using ball like abrasive particles.
根据三体磨损是典型的随机过程这一特点，运用蒙特卡罗方法模拟在球形磨料的作用下，材料塑性变形磨损的磨损率。
Monte Carlo method was applied for simulating plastic deformation wear rate of materials under the three body abrasion using ball like abrasive particles.
根据三体磨损是典型的随机过程这一特点，运用蒙特卡罗方法模拟在球形磨料的作用下，材料塑性变形磨损的磨损率。
应用推荐