非常剧烈的爆炸会损坏曲轴箱防爆门，引起机仓着火。
A very severe explosion can damage the crankcase door and cause fire in the engine room.
主轴箱中等主轴是车床的关键零件。
完成的曲轴箱和安装的是十字头指南。
The crankcases are finished and mounted as are the crosshead guides.
水分水汽在井喷的气体可以进入曲轴箱。
Moisture from water vapor in the blow-by gases can enter the crankcase.
曲轴箱连杆密封件损坏。
其中一半的负面模具和'内的曲轴箱'展开。
One half of the negative mould and the 'inside of the crankcase' mounted.
优越的分散性大大降低了曲轴箱油泥的形成。
Superior dispersiveness has reduced the forming of the crankcase oil sludge greatly.
在场的分散剂和洗涤剂增加发泡趋势曲轴箱油。
The presence of dispersants and detergents increase the foaming tendency of crankcase oil .
曲轴箱通风系统要携带新鲜的空气通过曲轴箱。
The crankcase ventilation system carries fresh air through the crankcase.
曲轴箱通风系统要携带新鲜的空气通过曲轴箱。
The crankcase ventilation system carries fresh air through the crankcase .
本文就机床主轴箱的瞬态温度分布提供一个近似解。
This paper presents an approximate solution of instantaneous temperature distribution of the headstock.
落座的阀门阻止火焰通过阀门和连接管进入曲轴箱。
Backseating the valve stops any flame from traveling through the valve and connecting hose into the crankcase.
单件气缸和曲轴箱总成发动机提供卓越的刚性，重量轻。
One-piece cylinder and crankcase assembly provides superior engine rigidity and light weight.
双方曲轴箱，建立了由失蜡法这意味着你必须作出负面的模具。
Both crankcases are established by the lost WAX method which means that you have to make a negative mould.
油盘和气缸体的下部一起被称为曲轴箱，用来封闭或罩住曲轴。
The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose, or encase, the crankshaft.
本论文为加工主轴箱箱体右侧十个螺纹底孔的组合钻床的设计。
This thesis combination machine for design processing many stalks the box ten screw threads of rights the bore bed.
汽车内泄漏污染物的四个位置是燃油箱、化油箱、曲轴箱和尾管。
The four places in the automobile from which pollutants can escape are the fuel tank, carburetor, crankcase and tail pipe .
机床主轴部件和主轴箱的热特性是影响机床精度的主要因素之一。
The Thermal Properties of Spindle Assembly and Headstock is one of the main elements that influence machining precision.
这类机床常见的有两种，可换主轴箱式组合机床和转塔式组合机床。
This machine has two kinds of common, spindle box combination machine tools and turn tower combination machine tools.
具体用法是把清洗剂倒入曲轴箱，怠速5到10分钟后，排出旧机油。
The usage is the cleaning agent into the crankcase, idle for 5 to 10 minutes, drain the old oil.
因此，没有证据显示这些液体机油来自曲轴箱通风和停留的各种装配管道…
So there is no evidence to show the liquid oil come from crank case ventilation and remain in the manifold assembly .
如果没有机油，压缩的气体会从曲轴箱溢出，这会对发动机的性能带来影响。
Without the oil, compression games would escape into the crankcase area, which will make effect on the performance of the engine.
由于高公差内曲轴箱不过，这可以是一个困难的，往往不是非常精确的任务。
Because of high tolerances inside the crankcase however this can be a difficult and often not very precise task.
根据模块化设计原理，在功能分析的基础上划分了组合机床多轴箱的各级模块。
According to modularization design principle, the modules of multi-spindle box of modular machine tool are divided on the basis of function analysis.
PCV系统将窜漏进曲轴箱的混合气引入进气系统，然后在燃烧室内进行二次燃烧。
PCV system will be a mixture of leaking into the crankcase leap into air intake system in the combustion chamber, then a second combustion.
一个短的工作在主轴箱主轴上通过适当简单的卡盘无需使用尾架中心也许就能被转动。
A short work may be turned without using the dead center, by simply chucking it properly at the spindle of the headstock.
一个短的工作在主轴箱主轴上通过适当简单的卡盘无需使用尾架中心也许就能被转动。
A short work may be turned without using the dead center, by simply chucking it properly at the spindle of the headstock.
应用推荐