This paper suggests a finite element analysis method of the multilayer pavement with materials of nonlinearity.
本文提出了一个考虑材料非线性的多层路面应力分析的有限单元法。
A finite element analysis is presented for predicting local buckling stresses in stiffened plates under axial compression.
本文给出了轴压加筋板局部屈曲应力的有限元分析。
The procedure and results of a finite element analysis on the oil distributing plate of an axial piston pump are introduced.
本文介绍了对轴向柱塞泵配油盘进行有限元分析的方法和结果。
A complete program, based on a finite element analysis, allows tooth proportion improvement increasing the life of the gearing.
一项已经完成的以有限元分析为基础的项目能够对齿的比例进行改善，从而延长了齿轮的工作寿命。
This paper introduced the method and result of conducting a finite element analysis on the cold forged reinforced thick wall tee joint.
本文介绍了对冷锻厚壁加强三通进行有限元分析的方法和结果。
This paper presents a finite element analysis of the thermal generation and temperature distribution of a vehicle's transmission gearbox.
对某车辆传动变速箱的温度分布，采用有限元方法进行了分析。
Study Design. A finite element analysis-based bone remodeling study in human was conducted in the lumbar spine operated on with pedicle screws.
研究设计：在人体以有限元分析为基础的骨重建的研究已经被运用于椎弓根螺钉固定的腰椎手术。
The software ANSYS is used to conduct a finite element analysis on its stress and displacement of typical working conditions for the improved support.
并利用ANSYS分析软件对改进后的支架进行了典型工况的应力及位移有限元分析。
In this paper, a finite element analysis of a bus body is introduced, Firstly, some assumptions and approximations used in this calculation are given.
本文介绍汽车车身车架结构计算机辅助设计的方法，根据有限元法计算出来的位移场和应力场探讨结构存在的问题和改造方案。
Finite element software of ANSYS has been used for making a finite element analysis of a certain type of ball-socket nozzle's pendulous socket in solid-rocket engine.
本文应用an SY S有限元分析软件，完成了对某型号固体火箭发动机珠承喷管摆动接头的有限元分析。
A finite element analysis demonstrated that minimizing bone and ligament removal resulted in greater preservation of normal motion of the lumbar spine after surgery32.
有限元分析证实，最低程度的切除骨和韧带能够更大程度的保留术后腰椎正常活动范围32。
Finally, based on the studies on the key technologies of the system, a finite element analysis system for cable-strut structure of point-supported curtain walls was developed.
最后，基于以上关键技术的研究，开发了点支式幕墙索杆结构有限元分析系统。
Taking the advantage of CAE powerful functions of ANSYS software, a finite element analysis of butterfly valve is realized, and the dimension and structure of valve body is optimized.
利用ANSYS软件强大的CAE功能进行碟阀的有限元分析，从而可以对碟阀的尺寸和结构进行优化。
Comparison of these results with the corresponding results from a finite element analysis indicates that good agreement is obtained, but the equivalent plate analysis is more efficient.
通过与有限元计算结果比较发现，两者吻合较好，但等效板方法计算效率更高。
Comparison of these results with corresponding results from a finite element analysis program indicates that good agreement is obtained, but the equivalent plate analysis is more efficient.
通过和有限元计算结果比较发现，两者吻合较好，但等效板方法计算效率更高。
This article makes a finite element analysis on the boring bar of combination boring-machine designed particularly for processing spindle holes of locomotive engines by using I-DEAS Master Series5.
针对镗杆在加工过程中的振动问题，结合碰撞减振理论及复合层叠材料力学原理，设计出了一套新型抗振镗杆。
This paper simulates the temperature field associated with laser surface quenching using ANSYS - a finite element analysis software, and a series of studies are carried out based on this simulation.
本文结合先进的大型有限元分析软件ANSYS，对激光表面淬火的温度场进行有限元模拟，并在此基础上，对此展开一系列研究。
This text mainly introduces a way of Finite Element to analysis the fine whetting outside circle of urn about the tongs.
本文主要介绍对已完成基本结构设计的气缸缸套精磨外圆夹具的有限元分析。
Mesh generating is a necessary procedure between geometric definition of part and its finite element analysis.
有限元网格生成是零件几何定义和有限元分析之间必不可少的步骤。
Based on the geometrical nonlinear finite element (GNFE) theory, a curved quadrilateral isoperimetric element with 8 nodes for initial form analysis of tensile membrane structures is presented.
本文根据几何非线性有限元理论，提出张力膜结构初始形态分析的8结点曲面四边形等参单元。
Possibility and efficiency in the application of this method to large finite element analysis are illustrated by an example of the stress analysis for a section of a cable stayed bridge.
以斜拉桥桥段的应力分析为例，说明在大型有限元分析中采用分阶段计算方法的可能性和有效性。
Based upon finite element simulation analysis, load tests and long-term observation, a detection and evaluation system for old steel bridge safety was developed in this thesis.
本文以桥梁仿真分析技术为主线，以整治效果为目标，以荷载试验和长期观测为检验手段，建立了既有钢桥裂纹安全检测评估系统。
The analysis result shows that it is a very feasible method for designing of nonstandard parts to adopt optimal technology based on finite element analysis.
分析结果显示，将基于有限元分析的优化技术应用于非标零件的设计是一种非常可行的方法。
Conclusion Three dimensional finite element analysis is a kind of convenient and practicable method to be used as the confirmation and supplement of experimental biomechanics study of human being.
结论三维有限元分析方法是一种简便实用的生物力学研究方法，可作为实验生物力学研究的验证和补充方法。
A numerical model based on the finite element method incorporating an arc-length algorithm for nonlinear full-range analysis of UPC beams was developed.
建立了基于有限元方法并结合一种弧长算法的适用于UPC梁非线性全过程分析的数值模型。
By comparing the results obtained from the test and finite element analysis, a very good agreement is found, showing the accuracy and feasibility of the simulation with finite element method.
将有限元模拟结果和试验结果进行了比较，取得了较好的一致，验证了有限元分析的正确性和可行性。
It is also presented a finite element analytical model suitable for non-linear analysis of HFB flexural members.
采用有限元方法，建立适于冷弯截面受弯构件性能分析的非线性有限元分析模型。
The paper USES finite element method to calculate the whole reel structure of a ship lift and presents the mechanical model of finite element analysis for the structure as a whole.
采用有限单元法对升船机卷筒结构进行整体计算，提出了有限元分析的力学模型，对筒壳、幅板的强度及刚度作了全面分析。
The paper USES finite element method to calculate the whole reel structure of a ship lift and presents the mechanical model of finite element analysis for the structure as a whole.
采用有限单元法对升船机卷筒结构进行整体计算，提出了有限元分析的力学模型，对筒壳、幅板的强度及刚度作了全面分析。
应用推荐