The viscosity, bulk and adhesive strength were tested.
测试了胶粘剂的本体强度、粘接强度和粘度。
The effect of polyvinyl acetals on its adhesive strength was investigated.
探讨了聚乙烯醇缩醛的粘接强度的影响。
Bitie surface with water-soluble glue, adhesive strength the blackhead removal.
鼻贴表面附有水溶性粘胶，通过粘力将黑头除去。
Adhesive strength, hardness and the thermal shock resistance of spraying coating were tested.
测试了喷涂层的结合强度、硬度以及抗热震性能。
The effects of coupling agent, filler and toughening agent on adhesive strength were also studied.
还研究了偶联剂、填料和增韧剂等对粘接强度的影响。
The adhesive strength and strength of resistance to impacting for the metal manufacture is better than normal epoxy.
对金属物品之接著，耐冲击强度优于环氧树脂。
The factors which influenced adhesive strength, curing speed of reactive polyurethane hot melt adhesive were studied.
考察了各因素对反应型聚氨酯热熔胶粘接强度、固化速度等性能的影响。
The average reliability of defects classification is over 80%, and the estimation of adhesive strength is satisfactory.
胶接缺陷的平均识别率在80%以上，胶接强度的估计精度也令人满意。
Dielectric barrier discharge (DBD) can be applied to modify polymer surface to improve its wettability and adhesive strength.
介质阻挡放电(DBD)处理聚合物表面可有效提高其亲水性和结合强度。
It is studied that the main influence factors on adhesive strength of CR adhesives, including mixed rubber, solvent, resin etc.
前言：研究了影响氯丁胶粘剂拉伸强度主要因素，探讨了混炼胶、溶剂、树脂等对氯丁胶粘剂拉伸粘接强度的影响。
It is studied that the main influence factors on adhesive strength of CR adhesives, including mixed rubber, solvent, resin etc.
研究了影响氯丁胶粘剂拉伸强度主要因素，探讨了混炼胶、溶剂、树脂等对氯丁胶粘剂拉伸粘接强度的影响。
The product has characteristics of strong adhesive strength, quick drying speed, high label-sticking rate and long storage time.
所制得的粘合剂具有粘合性强、干燥速度快、贴标率高、贮存期长等特点。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
介绍了三种典型的圆片键合强度表现形式：抗拉强度、剪切强度和粘接强度。
Experimental results indicated that the film on PZT had a excellent adhesive strength and a seawater corrosion resistant property.
实验结果表明：压电陶瓷表面化学镀的镀层具有优良的结合力和耐海水腐蚀性能。
Stable spraying process and uniform and compact coating with high adhesive strength can be obtained by using the expert controller.
研制的等离子喷涂专家控制器可实现对常用喷涂粉末的稳定喷涂并获得均匀致密和高结合强度的等离子涂层。
Wood floor adhesives should have properties of highly adhesive strength and good durability, water resistance and impact resistance.
木地板粘结剂应具有足够的粘结强度和良好耐久性、耐水性和抗冲击性能。
The results of this paper have shown that it is successful for improvement on the water proof and adhesive strength of PVF with TDI.
研究表明甲苯二异氰酸酯对聚乙烯醇缩醛胶粘剂耐水性改性是可行的并且能提高胶粘剂的粘接强度。
The adhesive strength decreases at beginning and then stabilizes or back_jumps to some extent after several times for thermal shock.
在经历多次的热冲击后，粘接强度先降低，而后趋于稳定，并呈现出一定程度的回升。
Testing the setting time, flexural strength, compressive strength, water retention, adhesive strength of gypsum with the adhesive agents.
对掺加粘结剂的脱硫石膏的凝结时间、压折强度、保水性能、剪切粘结强度的测试。
The result showed that this adhesive has advantage of high initial adhesive strength, good low temperature storage stability and low cost.
结果显示：该胶具有初粘性强，良好的低温储存稳定性及成本低廉等优点。
It was proved that high velocity arc spraying Ni-Al coating is one of best intermediate coatings with high adhesive strength and fine structure.
高速电弧喷涂镍铝涂层结合强度高，涂层组织致密，是优良的打底涂层。
The relationship between Brookfield viscosity and temperature, dip pick-up and adhesive strength of dip solution for PA6 tire cord was discussed.
讨论了锦纶6帘子布浸胶液布氏粘度与温度、附胶量、粘着强度的关系。
The content of PTFE powder filled in the epoxy adhesive can affect the impact strength, adhesive strength, hardness and dry-wear property of the adhesive.
介绍用聚四氟乙烯粉填充于环氧胶中，研究了粉的含量对冲击强度、粘接强度、硬度、干磨性能的影响。
A new method was explored to make a new type bioactive graded coating on titanium alloy for medical use and to improve its adhesive strength and stability.
本工作的目的是探索制备钛合金表面生物活性梯度涂层的新方法，提高涂层的结合强度及稳定性。
The factors affecting the Adhesive strength between Silicone Rubble and Aluminum during the course of manufacture of new Hot Printing Plate were investigated.
研究了新型烫印版制备过程中影响硅橡胶与铝板之间粘结强度的因素。
The mechanism of generating freezing adhesive strength was analyzed, providing a new approach to the research of anti-freezing adhesive theory and techniques.
分析了材料的冻黏强度机理，为冻黏防治理论与技术研究提出了新的途径。
The soil adhesive strength is mainly composed of capillary pressure and viscous resistance of the water film, which are affected by the nature of solid surface.
土壤粘附强度主要由毛细管作用力和界面水膜粘滞力构成，固体表面性质对其产生影响。
The density, hardness, bending strength, adhesive strength and ttibogy characteristic of the coating are measured in the test and the practical value is studied.
试验中间测定了涂层的密度，硬度，抗 弯强度，结合 强度以及摩擦学特性，并着重探讨了实用性。
The effect of kinds of polysiloxane coupling agents, different treatments on the adhesive strength has been investigated by using shear adhesive strength and SEM.
利用剪切粘接强度、SEM等方法，考察了有机硅烷偶联剂的种类和处理方法对丙烯酸酯类胶粘剂，粘接强度的影响。
The influence of arc spraying parameters on the adhesive strength and wear-resistance of JCW-B coating was studied by orthogonal design test and extreme analysis.
采用正交设计方法和通过极差分析研究了电弧喷涂工艺参数对J CW - b涂层结合强度和耐磨性的影响。
应用推荐