The bonding strength of the new adhesive completely meets the requirements of orthodontic adhesives.
这种新型粘合剂的粘接强度完全满足了正畸粘合剂的要求。
The layer is smooth with higher microhardness, corrosion and bonding strength by using the proper process.
在合适的电刷镀工艺下,镀层表面平整、光滑,具有较高的显微硬度、耐蚀性和结合强度。
The test results show that the adhesive has the characteristics of higher bonding strength and bright application prospects.
实验表明,该胶粘剂具有优良的粘结性能,有广阔的应用前景。
The interfacial diffusion of alloying element is important to microstructure, microhardness and interfacial bonding strength.
合金元素在界面两侧的扩散是影响材料显微组织、显微硬度及界面结合强度的关键。
The porous titanium coating with the graded apatite is expected to be applied in clinical orthopedics to enhance bone implant bonding strength.
具有表面梯度磷灰石涂层的多孔钛有望用于临床矫形,以提高种植体的生物活性和骨结合强度。
The bonding strength is as strong as that of bulk silicon.
硅片键合强度达到了体硅的强度。
That defects are mainly in interface of SDB affects bonding strength.
硅键合片的缺陷主要集中在键合界面,键合强度受到很大影响。
The properties of fired paste and the viscosity strongly affect diffusion bonding strength.
浆料的烧成特性和粘度对扩散连接强度影响较大。
At last, the approach of increasing bonding strength and decreasing shearing stress is presented.
最后,给出提高新老混凝土界面粘结强度和降低粘结面剪应力的方法。
The influences of ultrasonic power on heavy aluminum wire wedge bonding strength were investigated.
超声功率是影响粗铝丝引线键合强度的最主要因素之一。
This interfacial indentation method is suitable for use in those coatings with high bonding strength.
界面压入法适合于评价高结合强度的涂层。
Objective To study the effects of colour on diametral tensile strength and bonding strength of resin.
目的:研究颜色的不同对树脂粘结剂径向抗张强度及其与瓷粘结强度的影响。
The experiment methods of the bonding strength between deformed steel fiber and concrete was self-designed.
自行设计了异形钢纤维与混凝土粘结强度试验方法。
CONCLUSION: Polymerization shrinkage of composite resin has negative effect on bonding strength of adhesives.
结论:树脂固化时的体积收缩可在黏结层产生较大的应力,影响黏结强度。
A new method for measuring bonding strength between electroplated layer and substrate of diamond tool is proposed.
提出一种新的电镀金刚石工具镀层与基体结合强度测试方法。
In adhesive bonding repair using composite patches, the size of patch has an obvious influence on bonding strength.
在复合材料胶接修补中,补片的尺寸对胶接强度的影响非常关键。
There is evidence that the ha layers on the porous Ti can accelerate the bone growth and enhance the bonding strength.
已经证明在多孔钛表面制备HA涂层后,能提高骨生长速度及结合强度。
The results show that, because of different intrinsic toughness and bonding strength, failure occurs by different ways.
结果表明,由于镀层本身韧性和膜基结合强度的差别,镀层的失效表现为两种不同的剥落形式。
The bonding strength of the composite interface is reduced when too low or too high extrusion temperatures are employed.
挤压温度过高或过低导致界面结合强度降低。
The melting state of powder and bonding strength of coating did not vary much within spraying distance in the experiment.
在试验的喷距范围内,喷距对粉末的熔化状态和涂层结合强度均无明显影响。
The bonding strength of interface can be increased and the shrinkage of patching material reduced when adding 8% fly ash.
掺入8%粉煤灰还可提高界面粘结强度及减少修补材料的收缩。
Selection of adhesive for bonding strength fi eld pull-out tests of thermal insulation layer and substrate was introduced.
介绍了在保温板材与基层的粘结强度现场拉拔试验中粘结剂的选用。
Experimental results showed that the bonding strength of metal-coated diamonds with alloy or metals was improved markedly.
实验表明,渗覆金属处理可以使粘结合金或金属对金刚石的粘结力大大增强。
Objective:To study the effects of duty cycle and frequency of microarc oxidation(MAO) on the titanium ceramic bonding strength.
目的:观察钛试样在微弧氧化处理过程中,不同的占空比和脉冲频率对钛瓷结合强度的影响。
Three typical manifestations of wafer bonding strength were introduced as tensile strength, shear strength and adhesive strength.
介绍了三种典型的圆片键合强度表现形式:抗拉强度、剪切强度和粘接强度。
The bonding strength is ensured by the correct choice of substrate material, surface preparation, adhesive and process parameter.
粘合强度可以通过选择正确的基体材料、表面处理、胶粘剂和工艺参数得以保证。
The results indicated that increasing the deformation and a proper rolling temperature may improve obviously the bonding strength.
研究表明,增加变形程度和选择合适的轧制温度能提高复合板的界面初结合强度。
In the present paper, a new model, a layered composite beam, is presented for determining the interface bonding strength of materials.
本文提出了一个确定层状复合材料界面结合强度的新模型,即由两种材料交替完全粘结在一起的复合梁。
The bonding strength of joint zone made by direct and indirect bonding was evaluated and their fracture characteristics were analysed.
对直接连接和间接连接接头的接合强度进行了评估,并对接头断裂特性进行了分析。
The equipment for measuring bonding strength of gunning mix is developed, the structure, measuring method and application are presented.
开发出用于测定喷补料接着强度的试验装置,介绍了装置的组成、 测定方法和应用试验。
应用推荐