The crankshaft has three main bearing journals.
曲轴有三个主要轴承期刊。
The crank is an offset section of the crankshaft.
曲柄是曲轴的偏置部分。
The wings are driven by a crankshaft that is connected to a gearbox.
机翼由连接着齿轮箱的机轴驱动。
The crankshaft therefore must be adequately strong and wear-resistant.
曲轴因此必须要足够结实与耐磨。
The crankshaft serves to change the reciprocating power into rotary power.
曲轴的作用是把往返力变为旋转动力。
The second photo shows the crankshaft center bearing holder installed in the block.
第二图为曲轴中心轴承持有人安装在该区块。
In that way, the forces acting on the crankshaft are balanced and vibration is reduced.
以这种方式，在曲轴上的力将会达到平衡而且震动也会减少。
The nationalization of engine crankshaft blank for jetta bora and golf car was realized.
实现了捷达、来和高尔夫轿车发动机曲轴毛坯的国产化。
The connecting rod links its large end to the crankshaft and its small end to the piston.
连杆的大头与曲轴连接，小头与活塞链接。
Crankshaft is an important part of truck engine parts, and it is also a fast moving parts.
曲轴是一个重要的组成部分卡车发动机部件，而这也是一个快速移动的零件。
I may try to add some weight to the crankshaft and maybe offset the flywheel weight a little.
我可以尝试添加一些重的曲轴，并可能抵消飞轮重一点。
The flywheel mounts to the engine's crankshaft and transmits engine torque to the clutch assembly .
飞轮安装在发动机曲轴上，它将发动机的扭矩传递给离合器总成。
The piston converts the potential energy of the fuel into the kinetic energy that turns the crankshaft.
活塞把燃料的潜在能量转化成为动能，其将会转动曲轴。
As the piston strokes in its bore, the crankshaft rotates, pressurizing the opposite bore reverses rotation.
正如在其孔活塞杆，曲轴旋转，加压相反的孔反转旋转。
This paper introduces a design procedure about production line of crankshaft forging on engine of motorcycle.
介绍了摩托车发动机曲轴锻造生产线设计、设备选型以及对工艺、模具设计研究。
The mechanism consists of several parts like crankcase, cylinder block, pistons, connecting rod, crankshaft, etc.
这一机构有一系列部件组成，如曲柄箱、气缸体、活塞、连杆、曲轴等。
Semifinished main bearings require finishing and fitting after installation, so that the crankshaft must be taken out.
半精加工的主轴承安装后需要修整和调配，这样曲轴就必须拆下。
A fatigue reliability optimum design method for automotive engine crankshaft under various operation modes is presented.
本文提出了汽车发动机曲轴多工况可靠性优化设计方法。
Because the crankshaft is built up inside the case, the bases of the rods do not need to be split and bolted back together.
由于曲轴建立了内部的情况下，该基地的燃料棒不需要分割和螺栓重新走到一起。
A torsional vibration damper is used to reduce torsional vibrations on the crankshaft and in turn minimise component stress.
扭振减震器用于降低曲轴上的扭振，进而最大程度上减小部件应力。
For the secondary forces to be in balance, the rods connecting the pistons to the crankshaft would have to be of infinite length.
为了平衡不受控制的力，连接活塞和机轴的杆不得不变得无限加长。
The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose, or encase, the crankshaft.
油盘和气缸体的下部一起被称为曲轴箱，用来封闭或罩住曲轴。
Changing the mesh of the timing gear and the crankshaft gear allow intake timing adjustment relative to the crankshaft position.
改变网格的时间齿轮和曲轴齿轮允许摄入量的调整时间相对曲轴的立场。
If chain is not satisfactory, remove camshaft sprocket attaching bolt and remove timing chain with crankshaft and camshaft sprockets.
若正时链不令人满意，则拆下凸轮轴链轮固定螺栓，并拆下曲轴和凸轮轴链轮的正时链。
The flywheel marks and indentation are used for setting the valve and the ignition systems relative to prescribed position of the crankshaft.
飞轮标记与凹口可以用来确定阀门与点火装置系统的位置，其要根据曲轴的规定位置来确定。
The combustion process pushes the piston down the cylinder with great force turning the crankshaft to provide the power to propel the vehicle.
其燃烧过程产生的巨大力量的推动着活塞向下运行，带动曲轴而产生推动汽车的动力。
The combustion process pushes the piston down the cylinder with great force turning the crankshaft to provide the power to propel the vehicle.
其燃烧过程产生的巨大力量的推动着活塞向下运行，带动曲轴而产生推动汽车的动力。
应用推荐