This work studies the effect of curing time in mold on the strength and other properties of low cement corundum castables, exploring the feasibility of reducing the curing time in mold.
研究了模内养护时间对低水泥刚玉质浇注料强度及其他性能的影响，探讨了施工过程中缩短浇注料模内养护时间的可行性。
The compressive strength also varied with the curing time.
养护时间不同，其抗压强度有明显的差异。
The effects of curing time, temperature and bleeding capacity on ice-formation pressure of grout were studied.
研究了养护温度、时间及泌水率对灌浆材料结冰压的影响。
Compared with the chemically cured adhesives, it is convenient for practical use, and its curing time is short.
与化学固化粘合剂相比，其操作使用方便，固化时间短。
The composition provides improved and reproducible flow during the early stages of molding without compromising curing time.
该组合物在成型的早期阶段提供改善的和可重现的流动而不损害固化时间。
The influence factors on surface curing time of silicone rubber release agent vulcanized at room temperature were analyzed by experiments.
通过实验分析了影响室温硫化硅橡胶脱模剂表面固化时间的各种因素。
Modifying the curing process according to the result of the kinetic study, we are able to reduce the curing time designed by Huang in 2001.
利用反应动力学所得的结果来设计硬化过程所需的温度与时间，可大大缩短黄宏文在2001年时所设计的交联时间。
The effect of rolling condition and O/P value of phenolic resin on the curing time and flowability of phenolic resin for injection molding was studied.
考察了辊压工艺及酚醛树脂的邻对位比值（O/P）对酚醛注塑料的成型时间及流动性的影响。
Test shows that the curing temperature and curing time are the main factor which affect the whiteness fading and color change of printed white garment.
结果表明，白布在经后整理及成衣印花后，白度下降及颜色变化主要是由后整理及印花中的高温处理温度及时间引起的。
The effects of PPC content, curing agent, curing temperature, curing time and adding carbon black on the mechanical properties of the blends were studied.
研究了PPC的添加量、硫化剂的种类及用量、硫化时间、硫化温度和添加炭黑对共混弹性体的物理力学性能、交联度的影响。
The results show that nanometer microwave-absorber can obviously decrease the microwave curing time of modified epoxy adhesive under the same curing condition.
结果表明，在相同固化条件下，纳米微波吸收剂能明显降低改性环氧胶粘剂的微波固化时间。
The results showed that the increasing of curing temperature could improve the compressive strength and shorten the curing time of fly ash based mineral polymer.
结果表明：提高养护温度可以提高粉煤灰基矿物聚合物的抗压强度，缩短养护时间。
The amount of plasticizer, film thickness, curing temperature and curing time effect the release of the DS from the tablet coated with ethylcellulose aqueous dispersion.
结论 ：乙基纤维素水性分散体可作为缓释衣膜材料。增塑剂用量、衣膜厚度、后处理温度、后处理时间等因素均影响药物的释放。
On the basis of experiments and analysing the effects of the constant temperature and curing time on the strength of fly-ash, the best curing temperature and time are obtained.
在实验的基础上通过对恒温温度及养护时间对粉煤灰强度影响的分析，得出粉煤灰制品的最佳养护温度和时间。
Formulation, process conditions, curing time and flow behavior of phenolic resin for injection molding with excellent flowability and fast-curing characteristic were described.
介绍了一种高流动性快速固化酚醛注塑料的配方、制备工艺及其成型时间和流动特性。
Objective To study controlling method for curing time of the materials based on isocyanate , and perfect making means and operating rules of transmitting apparatus for the wounded.
目的：研究异氰酸酯基材料固化时间控制方法，以完善基于此材料的伤员固定转运器械的制作方法和操作规程。
Through analyzing each factor such as concentration of citric acid and chitin, curing temperature as well as curing time, the optimum condition is defined for the anti-crease finish.
对柠檬酸、壳聚糖及焙烘温度和焙烘时间等进行了单因素分析，确定了防皱整理的最佳工艺。
Influencing of curing time on film hardness is discussed through modifying the ratio of paint and curing agent. The defects from spraying process and the countermeasures are narrated.
通过调整漆与固化剂比例，讨论了固化时间对漆膜硬度的影响，同时论述了喷涂过程中产生的缺陷和采取的措施。
In this study, the effects of various contents of peroxide, amine, and inhibitor on polymerization degrees, mechanical performances, and curing time of dental resins were investigated.
考察了过氧化物、胺和阻聚剂含量对实验性化学固化树脂双键转化度、显微硬度、压缩强度、径向抗张强度、弯曲强度和固化时间的影响。
The real time monitoring for residual strain induced by resin cure during the RTM process was realized by measuring the relationship among wave deflection, temperature and curing time.
通过光纤光栅波长偏移与温度和固化时间之间的关系测试，得到了树脂固化过程中残余应变的变化历程，成功实现了RTM工艺树脂固化过程中残余应变的在线监测。
Effect of curing temperature, curing time, resistance to media, kind and volume of the sand-laden fluid, and particle size of proppant on fibre compound sand control system were discussed.
探讨了固化温度、固化时间、耐介质性、携砂液的种类和用量以及支撑剂粒径等对纤维复合防砂体的影响。
Research progress in influencing factors of properties of nano-filler ECAs, such as content, size, shape, surface state of nano-fillers, curing temperature and curing time etc, was reviewed.
从纳米填料含量、粒径、形状与维度、表面状态、固化温度与固化时间等方面综述了纳米填料导电胶性能影响因素的国内外研究进展；
Effects of process conditions such as different curing temperature, curing time, starting reaction temperature and casting flaw on polyurethane elastomers mechanical properties are investigated.
研究了工艺条件(不同固化温度、固化时间和初始反应温度)以及浇注成型产生的缺陷对聚氨酯弹性体力学性能的影响。
Effects of process conditions such as different curing temperature, curing time, starting reaction temperature and casting flaw on polyurethane elastomers mechanical properties are investigated.
研究了工艺条件(不同固化温度、固化时间和初始反应温度)以及浇注成型产生的缺陷对聚氨酯弹性体力学性能的影响。
应用推荐