Cutting depth can be controlled automatically adjust shades.
切割深度可自动控制调整深浅。
Mistracking led to product sliding and insufficient cutting depth.
Mistracking主导产品滑动和切削深度不足。
For positive chip angles, interrupted cutting and varying-cutting depth.
适合锐角的切削角度、切断操作和变切削深度。
Manage stripping and cutting depth through convex transmission, to ensure high stability.
使用凸输方式完成剥皮及进刀深度，稳定性高。
A useful method for adjusting the micro-cutting depth when machining holes on a round bar is presented.
介绍了一种方便实用、可在加工外圆、内孔时进行切深微量调节的方法。
The study would provide theoretical basis to the layout of the cutter installation at different cutting depth.
该研究对不同截深处截齿的安装布置提供了理论依据。
The limit cutting depth of the machining system with optimal controlling spindle speed is studied by experiments.
对优控主轴转速系统的极限切削深度进行了试验考证。
It discusses the water-jet cutting process by the balance of energy, and builds a mathematic model of cutting depth.
论文从能量平衡的角度探讨了射流切割的过程，建立了水射流切割深度数学模型。
To improve surface roughness should be considered from VF and cutting depth while the cutting speed is of a little use.
改善表面粗糙度应重点从进给量考虑和切削深度考虑，切削速度的影响是比较小；
To probe into machining mechanism in micro cutting, the minimum cutting depth for achieving stable machining was discussed.
为探讨微切削的加工机理，对能稳定切削的最小切削深度进行了研究。
Results showed that: in the same cutting depth, the force employed on the point-attack pick is bigger than that on the knife tooth;
试验结果表明：相同截深时锥形截齿截割力比扁型截齿截割力大；
The system consists of initial parameter and cutting depth input, cutting force and cutting power calculation, design result output.
该系统由原始参数、切削用量输入模块、动力参数计算模块、设计结果输出模块等几个主要模块组成。
Double oil cylinders drive, four-column guiding and automatic balancing are adopted to guarantee identical cutting depth for each time.
采用双油缸驱动，四柱寻向，自动平衡，确保每次裁断浓度完全一致。
The too small gas flow makes plasma arc lost due to the degree and straight cutting depth becomes shallow, but also easy to produce hang slag;
过小的气体流量则使等离子弧失去应有的挺直度而使切割的深度变浅，同时也容易产生挂渣；
Even if the date of back cutting depth is bigger in the parts of cutting velocity, the cutting system's chatter vibration might not be happened.
如果公称切削速度处于该稳定区域，即使背吃刀量较大，系统也不易发生颤振。
At the range of the testing parameters it is of advantage to select middle value of feedrate and cutting speed, and smaller value of cutting depth.
在本试验参数范围内选取切削参数时，切削速度、进给量取中值有利，切削深度取小值有利。
In single factor test, the influencing factor of tools wear was discussed, such as tool material, cooling conditions, cutting depth and feed speed.
以单因素实验法分别考察了刀具材料、冷却条件、切削深度、进给速度等对刀具磨损的影响规律。
The influencing orderliness of the cutting depth and the rake Angle of the tool on cutting qualities are found and the mathematical models are built.
得出了切削厚度与刀具前角这两个切削参数对切削质量影响的规律，得出二者关系的数学模型。
Contrast the two machining method between turn-milling and turning, research the effect on machining precision of micro-shaft parts about cutting depth.
通过车铣和车削两种加工方法的对比，重点研究了切削深度对微细轴类零件加工精度的影响问题。
With double oil cylinders, four-column guide and automatically balancing link rid structure to ensure the completely same cutting depth cutting position.
采用双油缸，四柱导向，自动平衡连杆结构，保证每一个裁断位置的裁断深度完全相同。
Double hydro-cylinders and accurate 4-column automatic balanced connecting-rod structure make sure every cutting position and cutting depth are the same.
双油缸，精密四柱自动平衡连杆结构，保证每一个裁断位置裁断深度完全相同。
With the increase of cutting depth, under the impact of abrasive particles with a large Angle, an oblique stripe deformation of the grinding zone are formed.
随切深的增加，材料在磨料粒子大角度冲击下形成斜条纹状的变形磨削区。
The clamping claw with high hardness, and intermittent cutting, so that when the cutting depth and cutting amount is small, the cutting speed is not too high.
因卡爪硬度较高，又系断续切削，所以修正时切削深度和走刀量要小，切削速度也不宜太高。
Theoretical analysis and experimental results all indicate that cutting depth is increasing with the decreasing of cutting speed and increasing of laser power.
理论分析和试验结果表明切割深度随着切割速度的减小而增加，随着激光功率的增加而增大。
With double oil cylinders, four-column guide and automatically balancing link rod structure to ensure the completely same cutting depth of each cutting position.
采用双油缸、四柱导向，自动平衡连杆机构，保证每一个裁断位置的裁断深度完全相同。
Road cutting through the slot machines four linkage cutting depth can be adjusted by cutting card round, saw no guarantee that deviation, and ensure accurate cutting.
路面切槽机通过四连杆机构可以调整切割深度，采用切割卡轮，保证锯片不跑偏，保证切割准确。
Double oil cylinder and precise four-column automatic balance connecting rod structure, which can guarantee the absolutely same cutting depth of each cutting position.
双油缸、精密四柱自动平衡连杆结构，保证每一个裁断位置裁断深度完全相同。
Four-column double oil cylinders mechanism and precise automatic balancing mechanism are adopted to reach high ton cutting force and ensure identical cutting depth at each point.
采用四柱式，双油缸驱动机构，精密自动平衡结构，达到高吨位裁断力，并保证每个点的裁断浓度完全一致。
Four-column double oil cylinders mechanism and precise automatic balancing mechanism are adopted to reach high ton cutting force and ensure identical cutting depth at each point.
采用四柱式，双油缸驱动机构，精密自动平衡结构，达到高吨位裁断力，并保证每个点的裁断浓度完全一致。
应用推荐