The situ dead load experiment verifies that the parameter in designing is reliable.
经过现场静载试验，验证了设计中取用参数的可靠性。
The failure time of elements in structural system under dead load and fatigue load was studied.
对在静载荷和疲劳载荷共同作用下的结构系统中的各失效元件的失效时间进行研究。
The testing content, loading mode, testing method and the testing results of dead load are introduced.
介绍了对该桥的检测内容、加载工况、测试方法以及静载试验结果。
The ultimate load of cable-stayed bridges is determined by the failure path of structure under the dead load.
在自重荷载作用下，斜拉桥极限承载力与结构的失效路径有关；
The skillful design of the pulley block makes the largest door leaf able to bear the 400kg dead load of the leaf.
滑轮组的巧妙设计，使最大门扇可承受400公斤的门扇自重。
The standard value from the spot dead load experiment is the most important and reliable basis of the stake base design.
采用现场静荷载试验所得到的单桩垂直承载力标准值是最基本、最合理的，它是桩基础设计最主要最可靠的依据。
The dead load shear and impact shear testing were performed from both of root apex direction and cutting edge direction.
测试了剪切力分别沿根尖方向和切缘方向作用的静剪切和冲击剪切强度。
About dead load effects, the relative deviation between calculated and measured strain is conducted statistical analysis.
在恒载效应方面，对应变的实测值与理论值的相对偏差进行了统计分析。
High strength steel sheet has been increasingly used abroad in order to reduce the dead load of automobiles and save energy.
为了减轻汽车自重，节约能耗，国外广泛采用高强度钢板，并研究了采用BH钢板后对车身外表零件抗凹陷性能的影响。
The emphasis is on the no - load, dead load and dynamic load test of all kinds of safety insurance device and the whole machine.
重点是各种安全保险装置和整机的空载、静载、动载试验。
Reliability index is influenced by the variance of basic parameters, resistance distribution, and ratio of live load to dead load.
可靠指标与极限状态方程中的各基本变量的变异性、抗力的概型分布、以及活荷恒荷效应比有关。
The surface mounting sensors have the advantage of being replaced, but they can not solve the issue of monitoring dead load stress.
表贴传感器具有可更换的优点，但不能解决恒载应力监测问题。
And then the effect of the change of cable length and span and the redistribution of dead load due to deformation on cable curve are analyzed.
分析了索长变化、跨度变化及主缆变形引起的恒载重分布对主缆线形的影响。
The pre-embedded approach can resolve the issue of monitoring dead load stress, but the long-term monitoring can not be achieved due to sensor life.
预埋的方式可解决恒载应力的监测问题，但存在因传感器寿命问题而不能实现长期监测；
To evaluate fracture instability, the total sum of stresses due to residual welding or rolling stresses, dead load, and live loads must be considered.
计算断裂失稳性时，必须考虑焊接或轧制残余应力，恒载应力和活载应力之总和。
In order to understand whether the new Tingjiang bridge of Dapu county after finished can satisfy the design requirement, it makes a dead load experiment.
为了解大埔县新汀江大桥成桥后实际承载能力是否满足设计要求，针对新汀江大桥进行静载试验。
The dead load experiment study for this system has been conducted for the first time in China. The bulging law of the hydraulic elastic bulging roll has been studied.
本文在国内首次完成了液压胀形轧辊系统的静载实验研究，初步探讨了液压胀形轧辊的胀形变形规律。
By contrasting curved bridge and straight bridge, influence of dead load and prestressing force on the stress in cantilever casting period of curved Bridges is analyzed.
通过曲线箱梁桥与直线箱梁桥的对比，模拟计算并着重分析了施工阶段自重、预应力等因素对曲线箱梁桥悬浇时应力的影响。
For equipment subject to considerable dynamic loads (e. g. heavy-duty fans) the individual load rates of the equipment are specified (dead load, live load and dynamic loads).
对承受较大动荷载的设备(如大型风机)，其荷载应分项注明。(包括静荷载，活荷载和动荷载)。
By analyzing the structural theory calculation, make sure the bridge dead load experiment plan, elaborate the experimental preparation, implementation process and the effect.
通过结构理论计算分析，确定该桥静载试验方案，阐述试验准备、实施过程及所取得效果。
In Chapter 5, problem of radial motion for a solid sphere composed of an imperfect incompressible hyper-elastic material, subjected to a surface tensile dead load, is examined.
第五章中，研究了具有缺陷的不可压超弹性材料组成的球体在表面均布的拉伸死载荷作用下的径向运动问题。
First, this paper introduces us the dead load experimental test equipment, the increasing load method, and how to confirm the pile foundation's vertical bearing weight through this way.
首先，本文介绍了静载试验的试验装置、加载方法，及如何通过静载试验测试数据确定桩基的竖向承载力。
Finally, the initial construction state and dead load state of Jiangyin Yangtze River Highway Bridge are calculated as a numerical example. It is shown that the initial construction sta...
运用该方法对江阴长江大桥进行了计算，计算结果表明：该方法能比较准确地计算出悬索桥施工理想初态和成桥状态。
The prime tasks were summarized as follows: 1. Space finite element analysis of the bridge was accomplished under the dead load and worst-case of live load adopting ANSYS and Midas separately.
完成的主要工作如下：1。采用ANSYS和Midas分别对全桥在恒载和最不利活载作用下进行了空间有限元分析。
Combined with in-situ loading test of a certain hydraulic project, the bearing capacity of soft sandy gravel rock foundation and the effect of dead load stress on the bearing capacity are discussed.
结合某工程现场载荷试验探讨砂砾软岩的极限承载能力及自重应力对极限承载能力的影响。
The finite oscillation and destruction of thermo-hyperelastic cylindrical shells subjected to a suddenly applied dead-load on the inner surface under different temperature fields were studied.
研究了热超弹性圆柱壳在内表面突加载荷及不同温度场作用下的运动与破坏问题。
The catenary theory and geometrical nonlinear finite element method were adopted in determining the dead-load state of self-anchored suspension bridge with spatial cables.
结合悬链线理论和几何非线性有限元方法，对空间缆索自锚式悬索桥成桥状态的确定方法进行了研究。
This paper introduces the structural inspection and dead-load experiment of certain service bridge structure, which provide the reference and basis for further research.
本文对某在役桥梁结构进行了全面的结构检测及静载试验研究，为旧有在役桥梁结构的检测鉴定及进一步的维修加固提供了参考及依据。
This paper introduces the structural inspection and dead-load experiment of certain service bridge structure, which provide the reference and basis for further research.
本文对某在役桥梁结构进行了全面的结构检测及静载试验研究，为旧有在役桥梁结构的检测鉴定及进一步的维修加固提供了参考及依据。
应用推荐