Divide in measured media deformation under pressure, was sealed by pressure to form a pressure equivalent to the p, conduction to pressure instruments that measured media pressure value.
隔膜在被测介质压力作用下产生变形，密封液被压，形成一个相当于P的压力，传导至压力仪表，显示被测介质压力值。
This paper deals with creep deformation and stresses of a spherical pot under high temperature and uniform internal pressure.
本文对高温、均匀内压作用下球罐的蠕变变形和应力进行了探讨。
An optimum algorithm is proposed to solve the geometrically nonlinear problem of large deformation of a cantilever under pressure on free end.
提出一种解决几何非线性问题的优化算法，研究了悬臂压杆的几何非线性大变形问题。
Twins and dislocation movement are two important deformation characteristics of silver nano powder under high pressure shock wave.
孪晶和位错运动是纳米银在超高压冲压波作用下形变的两个重要特征。
Based on the mechanical principle, shell structures are designed such that improved stability and capacity under deformation earth pressure and impulse load can be achieved.
根据地面大跨度板壳原理设计出网壳结构，该结构稳定性强，能承受较大变形地压及冲击荷载。
In order to study the pressure features and deformation features of soil under three different major stresses, complicated truly triaxial test are needed.
为了研究三个主应力不同情况下的土体强度和变形特性，需要进行复杂的真三轴试验研究，本文主要研究内容如下。
This paper describes characteristics and regularity of deformation of floor rocks under ground pressure.
阐述了采煤过程中底板岩层在矿压作用下的变形特征及其规律。
Holographic photograph is applied to study surface deformation of core-contained rock samples under single-axial pressure and visible image of off-surface displacement field is displayed.
用激光全息干涉法研究了在单轴压力下的镶嵌试件的表面形变，显示了离面位移场的可见图象。
In order to solve the eccentric worn problem of tubing, deformation finite element simulation of the eccentric worn tubing was carried out with ANSYS software under internal pressure and axial load.
为了解决油管偏磨问题，对内压和轴力作用下的无偏磨、单面偏磨和双面偏磨油管分别进行了有限元(AN - SYS软件)模拟研究。
In this paper, the strength and deformation characteristics of tailing under high pressure were studied with triaxial tests on three kinds of tailing.
本文通过三种尾矿砂的三轴剪力试验对尾矿砂在高压力下的变形与强度特性进行了研究。
Based on production conditions and data, this article discusses the varying contact length back-up roll deformation under the condition of equal contact pressure between rolls.
以某中板厂生产条件和数据为基础，讨论了变接触长度支承辊辊间接触压力相等时的轧辊变形情况。
The pressure under cap, axis force along pile and deformation of foundation were obtained from these tests.
通过埋设测试元件对承台土反力、桩身轴力及复合地基变形等进行了量测。
Under operation pressure, the 3 D deformation strain and stress of SRM grain with composite case is calculated.
对复合材料壳体的固体发动机药柱在工作内压作用下的变形和三维应力、应变进行了计算。
The mechanical behavior and deformation characteristics of lining structure in Yuanliangshan tunnel under high water pressure was analyzed by using 3d FEM numerical model.
采用三维有限元数值模型，分析圆梁山隧道高水压条件下衬砌结构受力及变形特征。
It is shown that Although the deformation curve under the pressure of axis is well consistent between micro-concrete and normal-concrete, the elastic ratio and strength are different.
试验表明，虽然微粒混凝土和原型混凝土的轴心受压变形曲线是大体“相似”，但两者的弹模和强度存在差异。
Particle breakage of rockfill materials is serious under high pressure, and its influence on deformation of rockfill cannot be ignored.
高应力作用下堆石料的颗粒破碎严重，其对堆石体变形的影响不可忽视。
The theory of liquid metal die forging is the understanding of the process which combines solidification under high pressure with forced feeding by plastic deformation.
液态模锻理论是对高压下结晶凝固和塑性变形下强制补缩复合过程的认识。
Stress and strain contours of the stator under an even inner pressure and a pressure difference, deformation distribution varied with pressure were obtained.
对定子和螺杆进行接触计算，结果表明：定子与螺杆在圆弧顶接触时，剪应变和变形最大；
This whole needle valve type hot runner injection under low pressure, the injection molding products in contraction deformation is smaller.
针阀整体式热流道在低压下注射使注塑品在收缩时变形更小。
The results show that the metamorphism and deformation of the Shuangqiaoshan Group happened under the condition of low middle temperature and pressure.
结果表明 ，双桥山群岩石所经历的变质变形温压条件为中低温低中压条件。
The computing data indicates that because cartridge cases are thin walled cylinders, the emission stress and plastic deformation are high under gun pressure.
应用非线性有限元方法计算药筒的发射应力和抽壳力。
This whole needle valve type hot runner injection under low pressure, the injection molding products in contraction deformation is smaller.
针阀整体式热流道材料浪费少，注塑产品的质量得到改善并更加稳定。
This whole needle valve type hot runner injection under low pressure, the injection molding products in contraction deformation is smaller.
针阀整体式热流道材料浪费少，注塑产品的质量得到改善并更加稳定。
应用推荐