The elastic deformation of the rock can be measured by grating.
岩层在弹性范围内的变形可由光纤光栅测出。
This model considered the instant elastic deformation and nonlinear creeping.
该模型考虑了瞬时弹性变形及其蠕变的非线性特性。
The deformations in consideration include contact deformation and elastic deformation.
考虑的工件变形包括接触变形和弹性变形。
Fracture surface consists of plastic yield deformation area and elastic deformation area.
断口主要分为塑性屈服变形区和弹性变形区两部分。
However, the elastic deformation behavior of nanotubes is not affected by the strain rate.
然而，应变率对纳米管的弹性变形没有影响。
Most solids, if pulled or twisted, will give a little in a process known as elastic deformation.
大多固体，一经拉伸或弯曲，都会出现弹性变形这一过程。
The elastic deformation, the inner mechanism and the rigid motion of systems can be properly considered.
分析中可考虑体系的弹性变形、内部机构和刚体运动。
We also found that the diffraction rocking curves can reflect the elastic deformation degree of diamond.
实验中发现衍射摇摆曲线能够反映金刚石的塑性变形程度。
Considering the elastic deformation of the barrel, the AA gun is simplified into a multi-rigid body dynamic model.
同时考虑身管弹性变形，建立了火炮发射时的多刚体动力学模型。
During normal operation the couplers are capable of absorbing normal compression loads by elastic deformation only.
正常运行时，联轴器能够吸收仅有弹性变形产生的正常抗压荷载。
There are only elastic deformation and brittle deformation on the process of hydraulic fracturing, and not compaction.
水力劈裂过程只有弹性变形和脆性破坏，不存在裂隙压裂过程中的第三种变形机理—压缩破坏。
Elastic pressure meter is made in accordance with the principle that elastic deformation caused by pressure of tested medium.
弹性式压力表是利用弹性元件在被测介质压力作用下，产生弹性形变的原理而制成的。
The analysis and calculation indicates that the power loss induced by the elastic deformation of rubber hose can not be ignored.
通过分析及计算表明：软管的弹性变形所消耗的能量是不容忽视的。
The film thickness is analyzed with elastohydrodynamic lubrication theory, tooth elastic deformation computed by finite elements.
并利用弹流理论来研究啮合轮齿间油膜厚度，用有限元法来研究轮齿受载弹性变形。
We also analyse the critical velocity, at which elastic deformation translate to plastic deformation when the bullet impact the tube.
同时也分析了冲头对圆管碰撞时，导致圆管由弹性变形向塑性变形转化学的临界速度值。
Roll elastic deformation must be considered when plate rolling mill is designed and rebuilt and plate shape is controlled and improved.
在设计、改造板带轧机，以及控制和改善板形时都要对轧机辊系弹性变形进行考虑。
Using an engineering example, this paper discusses the method of determining elastic deformation criterion for earth roadbed in detail.
结合工程实例，详细论述了土方路基回弹弯沉检测标准的确定方法。
The results show that the micro rotational Angle induced by the tooth surface elastic deformation has definite effect on meshing points.
结果表明，齿面弹性变形引起的齿轮轮齿的微小转动对啮合点的最终位置有一定的影响。
There exists the elastic deformation during the process of sheet bending, and it will influence the springback of sheet after unloading.
板料在弯曲过程中，由于存在弹性变形，卸载后，弹性变形必然影响到板料的回弹。
This article describes that ZIS, through analysing the elastic deformation of the work roll and supporting roll, optimizes the roll crown.
通过对带钢平整过程中工作辊和支撑辊受力、变形等特点的分析，优化了轧辊辊型。
The pressure proportional elastic deformation of this bourdon tube is transmitted through a low friction movement to the knife edge pointer.
波登管的压力比例塑性变形通过摩擦力很小的机械装置传递给刃形指针。
The magnitudes of elastic deformation and elastic deformation energy can reflect the stability and vibrations of the flexible robot systems.
提出了评价柔性机器人系统性能的变形度指标和变形能量度指标。
Elastic deformation is an important influential factor of indexing accuracy and loading capacity of end-tooth indexing table with drum tooth.
齿廓弹性变形是影响鼓形齿端齿盘精度和承载能力的重要因素。
The results show that the influence of thermal deformation on the bearing performances is smaller than that of thermal - elastic deformation.
结果表明热变形对轴承性能的影响较小，而热弹变形对轴承性能影响较大。
In finite elastic deformation, the direction and the density of the boundary force can greatly change with the deformation of the elastic body.
在有限弹性变形中，边界力的方向与密度将随弹性体的变形而发生显著变化。
Comprehensive function of varying contact length backup roll (VCR) is analyzed by using the finite element model for elastic deformation of rolls.
利用建立的有限元辊系弹性变形模型，分析了变接触支持辊(VCR)的综合性能。
Through an example, the influence of the elastic deformation and each random parameter on the mechanism reliability of motion function is analyzed.
通过算例，分析了机构的弹性变形和各随机参数对机构运动功能可靠性的影响。
A method of energy difference between elastic deformation and elastic-recovery deformation is developed to determine the residual deformation energy.
本文提出用弹性变形能与弹复变形能的差值来确定残留变形能的方法。
Valve gear is regarded as stiffness in the traditional design and its elastic deformation in motion is neglected. This method is called static design.
配气凸轮传统的设计方法是把配气机构看成绝对刚体，不考虑它在运动时的弹性变形，这种设计也称为静态设计。
Valve gear is regarded as stiffness in the traditional design and its elastic deformation in motion is neglected. This method is called static design.
配气凸轮传统的设计方法是把配气机构看成绝对刚体，不考虑它在运动时的弹性变形，这种设计也称为静态设计。
应用推荐