Applicable to 2, 3, 4, 6 flutes HSS end mill, carbide end mill, reamer.
可刃磨2,3,4,6槽的高速钢铣刀，硬质合金铣刀的端刃和螺旋刃。
Single-edged aluminum milling cutter----the best end mill for various aluminum panel.
单刃铝用铣刀-------最适合雕刻机加工切割铣削各种铝板。
Operation time: Complete in 2 minutes including setup time for 13mm 2 flutes end mill generally.
操作时间：通常情况下，1个13mm直径的2槽铣刀可以在2分钟内完成刃磨（含设定时间）。
Therefore, we can predict the variation of the cutting forces during the end mill moving along the ruled surface.
因此，刀侧贴著直纹曲面移动的切削力变化，可以模拟预测。
The helicoidal surfaces are produced mostly by form cutting with forming cutters of end mill type, side mill type or disc type.
螺旋面大多数是用球头铣刀、侧铣刀、盘形刀具成形加工出来的。
So improvements of the obdurability of the tool tips and cutting edges are very important to better the cutting property of the end mill.
刀尖是刀具中最薄弱的环节，提高刀尖及切削刃的强韧性对改善刀具切削性能尤其重要。
Workpieces with the cutter location points on the same plane are usually milled by window-frame method by 2-axis NC machining with flat-end mill.
环切加工是常用的数控二轴联动铣削方式，用于加工工位在同一平面上的零件；
It has an important value for forecasting milling force for the ball end mill and offers a reference for further improving surface machining quality.
切削力模型的建立对实现球头铣刀切削力的预报具有重要的现实意义，并为进一步提高表面加工质量奠定了基础。
Based on equation of cutting edges, new geometric model and NC grinding model of rake face of ball end mill with constant normal rake Angle are modeled.
本文基于刀刃曲线方程，推导了球头等法前角前刀面的几何模型及其数控磨削模型。
Let the finite element analysis method be introduced into the CAD of carbide end mill, and carry out an analysis on the strength and rigidity of the cutter.
将有限元分析方法引入硬质合金立铣刀CAD中，对刀具的强度、刚度进行分析。
Based on the cutting experiment, the changing rule of the cutting force in the high-speed milling of casting aluminum ZL101 by the end mill with three edges is discussed.
通过切削实验，研究了用三齿立铣刀高速铣削ZL101铸铝时切削力的变化规律。
Established three-dimensional solid model of ball end mill , and which is imported into ANSYS software, a static analysis and modal analysis are finished with the ball end mill.
建立球头铣刀三维实体模型并导入ANSYS中，对球头铣刀进行静态分析和模态分析。
Because of complex structure, traditional designing methods can not be used to do intensity analysis, stiffness analysis and stress analysis precisely for solid carbide end mill.
由于整体硬质合金立铣刀形状结构复杂，传统的设计方法无法对刀具进行精确的强度、刚度及应力分析。
The experimental results showed that high quality of cavity surface can be obtained by using appropriate technologic parameter and trochoidal milling mode with micro-end mill cutter.
试验结果表明：采用小直径刀具，合适的工艺参数，次摆线分层走刀方式能加工出高质量的型腔表面。
In the geometry modeling of ball end mill cutter, consideration of cusp effect of ball milling, accurate cutting Angle range corresponding to different axial cutting depth are deduced.
在球头铣刀几何建模中，考虑铣刀残余高度的影响，推导了不同轴向切深时对应的切入角与切出角范围。
Based on the models and the free-form surface formula, the moving envelope surface of ball-end mill is obtained by means of matrix calculating, the topography is modeled and simulated.
基于自由曲面方程，由矩阵运算得出刃线运动包络面，对球头铣刀加工的表面形貌进行了建模和仿真。
Vibration frequency of ball end mill by an external force is far from the natural frequency of it, resonance phenomenon does not occur, so vibration and deformation of ball end mill are not abvious.
球头铣刀在外力作用下的振动频率离固有频率较远，不会发生共振现象，由此引起的刀具振动和变形较小。
Compared to the photos at the top of the page, these photos show the longer rails (cut on a Sherline CNC mill) and generator at the end of the engine.
比起照片上方的网页，这些照片显示的时间越长轨(切断对Sherline数控轧机)和发电机结束时的引擎。
At last, narcissa hurried up a street named spinner 's end, over which the towering mill chimney seemed to hover like a giant admonitory finger.
最后纳西莎赶到了一个叫做蛛尾巷的小道上，从这儿往上望去，磨粉厂的烟囱高耸著，就像一个巨人在晃动他警告的手指。
But Mill failed to remain in its logical consistency. And the conflict between "harm principle" and "utility principle" runs through from beginning to end of his theory of freedom.
但是，密尔在具体的论证过程中并没有保持逻辑的一致性，其“伤害原则”与“功利原则”的冲突贯穿于他的自由理论的始终。
This paper introduces the harms of the leakage on the end - cover of grate mill, analyzes on its causes, and puts forward some corresponding measures and methods for control.
介绍了格子磨端盖漏料的危害，分析了端盖漏料的原因，提出了相应的治理措施与方法。
A method is presented by using computational geometry techniques to determine optimal tool position and orientation for 5-axis machining with torus end-mill.
应用计算几何技术来决定优化的刀具定位和刀具姿态以实现环形刀的5轴自由曲面数控加工。
When taking compact mill as rough stands of high speed wire mill, the tensile force for biting and stable rolling are different, resulting in the dimension variation at end and middle part of product.
以紧凑式轧机作为高速线材粗轧机组时，由于粗轧中各机架咬入和稳态轧制的张力不同，致使坯料出口头尾尺寸波动较大。
In compliance with German DIN6527, DIN6528 and other international standards, our company specializes in producing plain mill, ball-end-mill etc.
我们公司根据德国DIN6527，DIN6528等其他国际标准，生产平面铣刀，球头铣刀等。附件有我们生产的产品信息，请查阅。
In the end, we give out a run-of-mill valuation method on the base of linguistic logic, which can reduce the decision deviation of selecting the numeric scale by error.
最后，基于合理的语言逻辑假设，给出了一种一般性的评价方法，以便于决策者在实际应用中选择适当的数字标度进行决策，降低了由于数字标度选择不当而带来的决策偏差。
Mill takes the achievement and guarantee of individual rights as the first be-all and end-all and treats' priority of utility 'as the first principle of justice.
穆勒以个人权利的实现和保障作为正义的第一要义，把“功利优先”作为统摄正义的第一原则。
In this paper, the reform process of the welding equipment and the choice of welding parameter about CO2 enclosed-arc welding as skelp end-welding in welded steel pipe mill are introduced.
介绍了管子、带钢接头co 2气体保护自动焊焊接设备的改造过程及工艺参数选择。
In this paper, the reform process of the welding equipment and the choice of welding parameter about CO2 enclosed-arc welding as skelp end-welding in welded steel pipe mill are introduced.
介绍了管子、带钢接头co 2气体保护自动焊焊接设备的改造过程及工艺参数选择。
应用推荐