For GUI programs, the hardest part can be recognizing whether the application indicated the right failure mode.
对于GUI程序，最困难的部分是辨认出应用程序是否检测出正确的故障模式。
The failure mode differs with the fibre hybrid.
纤维混杂可以改变材料的破坏模式。
Compare and contrast the different types of failure mode effects analysis (FMEA).
比较与对照不同类别的失效模式影响分析(FMEA)。
Resolves the problem of steering screw's reliability calculation in multi-failure mode.
解决了螺杆在多失效模式相关时的可靠度计算问题。
For each failure mode, an explicit formula is derived for the prediction of shear strength.
对于每一种破坏模式，给出了受剪承载力计算公式。
Low cycle multiaxial fatigue failure is the main failure mode of aeroengine compressor disk.
低循环多轴疲劳失效是航空发动机低压压气机轮盘的主要失效形式。
Interface failure is a common failure mode which is observed in reinforced composite materials.
界面失效是增强复合材料中常见的失效模式。
Moreover, the formula to judge the joint failure mode is set up and verified by the test results.
此外，还给出了节点破坏形态的判别公式，并用试验结果进行了验证。
The basic failure mode of borehole is borehole avalanche and shear zone caused by bore instability.
井眼基本破坏形式是由于不稳定性造成的井眼岩石崩落坍塌和剪切带。
Formulating actions to prioritize avoidance of potential failure mode with high risk identified in DFMEA.
制定措施优先减少风险大的潜在失效模式。
Weld access hole geometry and size have significant effect on ductility and failure mode of the connection.
节点局部构造尤其是焊接孔形状尺寸对于节点应力集中情况和节点破坏模式有很大影响。
Under the action of multiple stresses, contact failure is the main failure mode of aerospace electrical connectors.
在温度和振动等综合应力的作用下，航天电连接器的主要失效形式为接触失效。
The failure mode and failure mechanism for white ceramic DIP's are analyzed, and experimental simulation is performed.
简要分析了白瓷双列直插外壳的失效模式和失效机理，并进行了模拟实验。
To establish and verify the failure mode, trouble reappearing and low -cycle fatigue tests are conducted on component test rigs.
为确定与验证锥齿轮故障模式，在试验器上进行故障再现试验及低周疲劳试验。
The results clearly illustrate the load transfer mechanism in the deep pile cap and the subsequent failure mode of two-way shear.
结果清楚地显示，深承台板的载荷传递机制与相应的双向剪切破坏模式。
By tracing the change of the index of member importance due to failure of members, the most important failure mode is determined.
通过跟踪结构杆件的破坏顺序以及结构杆件重要性的变化，确定结构最重要破坏模式。
There are many failure modes of plastic parts during trial molding process. Every failure mode is in relation to improper designs.
在试模过程中，成型的塑件有多种失效形式，而每种失效形式都和模具设计不合理有关。
The results show that localization will firstly occur at dam heel and dam toe, but the final failure mode depends on the dam shape.
结果表明拱坝的局部化最先出现在下游坝踵和上游坝趾，但其最终破坏形态与坝体型有关。
According to lineation stochastic programming, an effective algorithm is put forward for searching structure principal failure mode.
根据线性随机规划法，提出了一种寻找结构主要失效模式的有效算法。
The primary failure mode of commomly used circuit protective devices is short-circuit, and so is TVS (Transient Voltage Suppressor) .
常用电路保护器件的主要失效模式为短路，瞬变电压抑制器（TVS）亦不例外。
In view of the strength of materials, the operating condition and main failure mode of oil field equipment are analysed in this paper.
本文从材料强度的观点，分析了石油矿场机械的服役条件和主要失效类型。
The rigidity of the reinforced material influences the failure mode of the reinforced earth wall, so it also affects the design method.
加筋材料的刚度影响着加筋土挡墙的破坏形式，从而也就影响着其设计方法。
Aiming at the fracture failure mode of piping and uncertainty int he assessment process, pressure piping reliability method was put forward.
针对管道的断裂失效模式以及安全评定过程中存在的不确定性，提出了压力管道可靠性安全评定方法。
On this basis, it determines the failure mode of the slope rockmass and presents an important foundation for the rockmass mechanics analysis.
在此基础上，确定了边坡岩体的破坏模式，为边坡岩体力学分析提供了重要的基础。
The simplified formula of ultimate tension load is obtained in view of mix plastic-cone tension failure mode of the M10 plastic embedded part.
针对M 10型预埋件的塑胶-锥体复合拉伸破坏形态，得出极限拉伸荷载的简化计算公式。
Variable correlation is expressed with consequence graph in Bayesian Networks (BN), analysis of failure mode and effect of complex system is realized.
贝叶斯网络用因果关系图的形式表达变量间相互关系，实现复杂系统的故障模式和效应分析。
Debonding between steel and concrete is a common failure mode in composite structures, and it is indicated interfacial failure may be energy governed.
界面脱粘是钢-混凝土组合结构中的一种常见破坏方式，而一些研究结果表明钢-混凝土界面的脱粘可能是由能量控制的。
Debonding between steel and concrete is a common failure mode in composite structures, and it is indicated interfacial failure may be energy governed.
界面脱粘是钢-混凝土组合结构中的一种常见破坏方式，而一些研究结果表明钢-混凝土界面的脱粘可能是由能量控制的。
应用推荐