• When finishing mill system vibrated violently, vibration response and operation parameters were measured.

    在精轧机系统发生强烈振动的情况下,对振动响应和运行参数进行了测试。

    youdao

  • It has been proved that high Cr cast iron rolls are fit for finishing mill of 1549 hot strip mill of Tisco.

    介绍了高铬轧辊化学成分和生产工艺,实际使用证明高铬轧辊适合太钢1549热连轧精轧机组。

    youdao

  • The working conditions and requests of the roll used in high-speed wire pre -finishing mill are introduced.

    介绍了高线须精轧机使用的轧辊(辊环)的工作条件和要求。

    youdao

  • The variation of mean flow stress of two kinds of low carbon steel rolled in Angang 1780 finishing mill were analyzed.

    本文分析了鞍钢1780生产的两种低碳钢在热连轧过程中平均流变应力的变化。

    youdao

  • The article describes the main drive gear reducer structure at finishing mill area of strip hot continuous rolling plants.

    简要介绍带钢热连轧机精轧区主传动减速机的结构特点。

    youdao

  • This paper describes the coilbox speed control and speed matching of coilbox and rougher, finishing mill, delivery table etc.

    介绍了热连轧机中热卷箱的速度控制及其与轧机和辊道的速度匹配关系。

    youdao

  • The reclaiming process can be simply carried out on an open mill or finishing mill at the room temperature without any pollution in the production.

    复原胶生产工艺简单,在常温下用开炼机或精炼机即可,而且生产过程中无污染。

    youdao

  • Cooling control system between finishing mill regulates the water-flow with electric signal and compressed-air to control the temperature of the hot strip steel.

    精轧机机架间带钢冷却控制系统,用电气控制信号和压缩空气联合控制冷却水的流量,从而达到热轧带钢温度控制的目的。

    youdao

  • The method and example of pass optimization design of high speed wire rod finishing mill by dynamic programming with minimum total tension coefficient are described.

    阐述了以动态规划法按最小总张力系数对高速线材轧机精轧机组孔型进行优化设计的方法与实例。

    youdao

  • The Load-Commutated Inverter(LCI) fed synchronous motor control system which is applied to the main drive for high speed wire finishing mill of Baotou Iron and Steel Co is presented.

    介绍了用于包钢高速线材厂精轧机主传动中的负载换流同步电动机控制系统。

    youdao

  • The try-out result shows that the newly developed cooling water valve can meet the finishing mill"s temperature control demands with expected effects in its performance and maintenance."

    试用结果证明新研制的冷却水阀满足了精轧机轧制温度控制的要求,在性能和维护方面达到了预期的效果。

    youdao

  • It has been analysed the causes for the heavy surface spalling of back-up roll for a finishing mill. The result shows that the main causes are gas hole, shrinkage and bad heat treatment.

    对连轧机精轧支承辊大面积剥落的原因进行了深入的分析,结果表明,轧辊内部的缩孔、气泡及热处理不当是造成轧辊表面剥落的主要原因。

    youdao

  • To reduce the weight and cost of finishing mill to the minimum, optimum design computes the important parameters with constrained cyclic coordinate method, and precision is improved further.

    而辊系优化推理部分以降低精轧机重量和减少造价为目的,采用约束坐标轮换法对辊系和机架参数进行优化推理,进一步提高设计精度。

    youdao

  • The chemical component and producing process of high Cr cast iron r ol l are introduced. It has been proved that high Cr cast iron rolls are fit for finishing mill of 1549 hot strip mill of Tisco.

    介绍了高铬轧辊化学成分和生产工艺,实际使用证明高铬轧辊适合太钢1549热连轧精轧机组。

    youdao

  • The Finishing mill F3 repeatedly occurs accidents of rolling crack and stopping steel plate in debugging production stage of thin slab concasting and conrolling production line in Bengang.

    本钢薄板坯连铸连轧生产线在调试生产阶段,精轧机F3多次出现轧裂卡钢停产事故。

    youdao

  • The Finishing mill F3 repeatedly occurs accidents of rolling crack and stopping steel plate in debugging production stage of thin slab concasting and conrolling production line in Bengang.

    本钢薄板坯连铸连轧生产线在调试生产阶段,精轧机F3多次出现轧裂卡钢停产事故。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定