This chemical mimics the effects of emotional or physical stress by increasing the force of heartbeats and boosting the flow of blood in the body, which can lead to permanently raised blood pressure.
多巴酚丁胺这种化学药品通过增加心跳力度以及加速血液在身体中的循环来模拟情绪或身体压力带来的效果。
Just as electrical energy generates heat when it meets resistance so our psychic energy generates tension and stress when it has to flow through areas that aren't our preference.
就像电子遇到了电阻时能量产生热量那样，当我们的心理能量流向不喜欢的领域时，我们就会产生紧张和压力。
The results showed that the flow stress of this alloy reduced with increasing deform temperature and increased with increasing strain rate.
试验结果表明，该合金流动应力随着变形温度的升高而下降，随着应变速率的增加而增加。
The flow stress of 7A60 ultra high strength aluminum alloy was studied by isothermal compress test at constant strain rate.
采用等温恒应变速率压缩试验对7A60超高强度铝合金的流动应力进行了研究。
The influences of softening modulus and elastic modulus on local damage variable rate depend on the flow stress level.
降模量及弹性模量对局部损伤变量率的影响取决于流动应力的大小。
During the isothermal constant strain rate compression process, the effect of deformation heating on flow stress increases with increasing equivalent strain rate.
在等温恒应变速率压缩过程中，随着等效应变速率的增大，变形热效应对流动应力的影响程度增大。
True strain, strain rates and temperatures were input parameters of the model, while flow stress was the only output parameter.
在该模型中，等效应变、等效应变速率和变形温度是模型的输入向量，输出向量是材料的流动应力。
Based on the crystal plasticity theory and mathematical theory of statistics, the relation of flow stress fluctuation quantity to grain dimension as well as billet dimensions was built.
基于晶体塑性理论及数理统计理论，建立了流动应力波动幅度与晶粒尺寸和坯料几何尺寸间的关系。
The results showed that the flow stress of tantalum was very sensitive to the changes of temperature and strain rate.
结果表明，钽的流动应力对温度和应变率的变化相当敏感。
In the past years, the models of flow stress were mainly focused on deformation temperature, deformation speed and deformation degree, but seldom on dislocation density.
而以往的流动应力模型主要考察变形温度、变形速度和变形程度，对位错密度的研究很少。
The main factor influencing computational accuracy of rolling load is the accuracy of material's flow stress.
分析了影响轧制力计算精度的主要原因，即来源于流动应力的准确性。
If, when the stress is removed, the deformation remains, the material is said to exhibit plastic flow.
如果在撤去应力后变形仍保留，则称此材料呈现塑性流动。
Change your diet, start exercising, practice stress management and quit smoking, and your brain gets more blood flow, so you think more clearly, have more energy and need less sleep.
改变你的饮食习惯，开始运动，实行压力管理，戒烟，这样你的大脑才能获得更多的血流量，你也因而可以更清晰地思考，更有活力，需要更少的睡眠。
The variation of mean flow stress of two kinds of low carbon steel rolled in Angang 1780 finishing mill were analyzed.
本文分析了鞍钢1780生产的两种低碳钢在热连轧过程中平均流变应力的变化。
The results show that the flow stress and peak strain increase with increasing strain rate or decreasing deformation temperature.
结果表明：实验条件下，流变应力及峰值应变随变形温度的降低和应变速率的提高而增大。
The distributions and changes of the contact pressure, flow stress and velocity field on the welding plane were analyzed.
分析了不同分流模模桥结构下焊合面上接触压力、流变应力和速度场的分布及其变化。
The results showed that the flow stress and deformed microstructure were greatly affected by strain rate and deformation temperature.
结果表明：应变速率和变形温度对合金的流变应力与变形组织有显著影响。
The results show that relationship between flow stress and strain rate is applied to hyperbolic sine equation in the hot compressive deformation of 6061 aluminum alloy;
研究表明，6061铝合金热压缩塑性变形时的流变应力和应变速率之间的关系满足双曲正弦函数关系式；
The maximum flow stress decreased with the increase of the temperature, furthermore, the reduction speed decreased with the increase of the temperature.
峰值流变应力随着变形温度的升高而下降，且下降速率随着温度升高而降低；
It was pointed out that the flow stress decreases with the increase of deforming temperature, while increased with the increasing of strain rate.
结果表明，流变应力随着温度的升高而降低，随应变率的升高而增大。
The result indicates that models are good enough to exactly predict recrystallization grain size and flow stress of AZ61...
结果表明，所建立的网络模型具有优良的性能，能精确预测AZ61 B合金热变形条件下的再结晶晶粒尺寸及流变应力。
The influence of affecting factors on the dispersion process was reviewed from the aspects of agglomerate structure and the flow field stress on agglomerate.
从团聚体结构和外界流场对团聚体的应力作用两个方面综述了各因素对团聚体分散过程的影响。
Therefore, it is not stress distribution in certain even section but integrate stress flow inside the cap that should be considered.
因此，在厚承台设计时应考虑承台内部的完整应力流，而不是某一平截面上的应力分布。
By means of further analysis, solves the problem of the concentrated stress with magnifying arc radius and dividing the stress flow.
对此进一步分析，通过增大圆弧半径以及采取应力流分流的办法，最终解决这些应力集中问题。
Deformation velocity has no obvious effect on the flow of material, initial yield stress and flow stress.
变形速度对材料流动、初始屈服应力、流动应力影响不明显。
Based on the actual steel grade of production, the flow stress is measured under rolling condition, and the mathematical models are obtained.
以现场的钢种为样本，测定热轧条件下的流动应力，建立流动应力模型。
Results show that the elastic modulus and flow stress decreases with the increase of temperature, while the stress rises with the strain rate increases.
结果表明：弹性模量和流变应力随变形温度的升高而降低，而流变应力随应变速率的提高而增大。
And ANN model could predict the corresponding flow stress at different strain, but constitutive equations could only predict the peak stress depending on different strain rates and temperatures.
神经网络可以预测不同应变下的相应的流变应力，但是本构方程只可以根据不同的应变速率和温度来预测峰值应力。
At the same time, the HAWP solutions appeared strong flow stress and obvious shear thinning phenomenon.
同时，溶液表现出明显的屈服应力和良好的剪切稀释性。
At the same time, the HAWP solutions appeared strong flow stress and obvious shear thinning phenomenon.
同时，溶液表现出明显的屈服应力和良好的剪切稀释性。
应用推荐