Three-dimensional physical and mathematical models for the coupled heat transfer of natural convection in a liquid pool with heat source and forced convection in cooling coil tube are established.
建立了含内热源的液池内自然对流与冷却盘管内强制对流耦合传热的三维物理、数学模型，进行了相应的数值模拟计算。
The heat transfer of film boiling on an elliptical cylinder when forced convection coexists with volumetric force is investigated.
本文研究了体积力与强制对流共存时椭圆柱外的膜态沸腾换热问题；
An experimental study on forced convection heat transfer of single-phase water in vertical and horizontal narrow annuli was performed.
对竖直及水平窄缝环形流道内单相水受迫对流换热进行了实验研究。
It investigates experimentally mixed convection and heat transfer augmentation by forced jets in a large rectangular enclosure with a vertical cooling surface.
实验研究了在具有垂直冷却面的大型矩形腔体中因强迫射流造成的混合对流传热。
Therefore , the rule of the influence of the specialty of different anticorrosion surfaces on the flue gas forced convection heat transfer with condensation was obtained.
从而得出不同镀层表面特性对烟气受迫对流凝结换热的影响规律。
A two dimensional numerical analysis has been presented to determin the forced convection on wall-protruded heat block in parallel flat plates.
用数值计算法对平行平板通道内二维凸出块热源的强迫对流换热进行了研究。
Two phase flow forced convection boiling heat transfer on helical coiled tubes has been systematically studied.
对螺旋管中两相强制对流沸腾传热特性进行了试验研究。
Generally forced convection circulation heating device taking gas as heat transmission medium requires high temperature uniformity. So it is very important for selection of fans and control method.
对温度均匀性要求较高的电热设备，通常采用强制循环对流的加热方式，因此风机的选型及控制对能否达到要求的温度均匀性至关重要。
Method and formulae for calculating the mean forced convection heat-transfer coefficient of the blade surface, as well as for the blade passage's bottom wall, are introduced.
介绍了汽轮机动叶片叶身平均对流换热表面传热系数和叶片流道下壁面对流换热表面传热系数的计算方法和计算公式。
They heat foods in a forced-air convection oven that's kept between 160 and 170 degrees Fahrenheit. It takes about 20 to 30 minutes to rehydrate and heat an average meal.
他们用强对流烤箱加热食物，烤箱温度保持在华氏160度至170度之间，每顿餐的食物注水和加热时间是20至30分钟。
By using ABAQUS software, force convection elements were adopted to simulate the heat transfer between the coil and the forced convective hydrogen.
应用abaqus软件的强制对流单元，研究了在特定的气体流动条件下的钢卷与气体之间的传热。
Forced convection heat transfer of water and air in plate channels filled with sintered spherical particles was investigated experimentally.
本文对空气和水流过烧结青铜颗粒水平多孔槽道表面上的对流换热进行了实验研究。
Two phase forced convection heat transfer coefficients are correlated as function of Lockhart Martinelli parameter.
用修正L M关系式整理了两相强制对流放热系数。
At first, the physical mechanism was studied then the 2d compact numerical simulation model for natural convection and forced convection heat transfer analysis was built respectively.
本文首先对散热器工作的物理机制进行详细分析分别对自然对流换热情况和强制对流换热情况建立了简化的二维数值计算模型。
The experimental correlations for the forced convection-condensation heat transfer of flue gas in the heat exchanger are obtained by the experimental study result.
根据实验研究结果拟合出了肋片管式冷凝换热器烟气强迫对流凝结换热的实验关联式。
An experimental study has been carried out for the forced convection heat transfer in non-Newtonian fluid in a small scale square duct at low Reynolds Numbers.
对非牛顿流体在小尺寸方形通道内的低雷诺数受迫对流传热进行了实验研究。
It is shown that the forced convection over micro pin fin heat sinks is a very effective heat transfer mode.
本文以去离子水为冷却工质，对流体横向冲刷方形微针肋阵列热沉的传热特性进行了实验研究。
This software can be used for package -, board - or system-level CFD simulation, including natural and forced convection and radiation heat transfer.
该软件可用于封装，电路板及系统级CFD模拟，包括自然对流、强制对流和辐射传热。
In the chapter 4, the mainly aims at the study of thermal characteristic of heat sink with heat pipe under natural and forced convection.
第四章针对热管型散热器进行了在自然对流和强制对流下散热特性的研究。
Forced convection heat transfer of air in nickel and copper metal foams and two mini - fin structures was investigated experimentally.
本文对空气流过镍、铜材料泡沫金属结构和2种板翅结构的对流换热进行了实验研究。
Forced convection heat transfer of air in nickel and copper metal foams and two mini - fin structures was investigated experimentally.
本文对空气流过镍、铜材料泡沫金属结构和2种板翅结构的对流换热进行了实验研究。
应用推荐