Cycle polymer flooding method can reduce injection pressure.
周期注聚方式可以降低注入压力。
The injection pressure, timing, duration and rate depend on the engine speed and load.
喷油压力、喷油始点、喷油持续角和喷油率均取决于柴油机转速和负荷。
The injection pressure is commonly described as the surface pump pressure required to achieve injection.
注入压力普遍地是指实现注入所需的地面泵压。
Water injection efficiency depends on whether the injection pressure is high or low in water injection Wells.
注水井注水压力的高低直接影响水井的注水效率。
The influences of injection pressure and injection temperature, two important injection parameters, were studied.
研究了注射压力和注射温度这两个重要的注射参数对注射坯体质量的影响。
Anew forecasting method of wellhead injection pressure for polymer flooding is established based on Dupuit formula.
依据裘比公式建立了一种新的聚合物驱油井口注入压力预测方法。
Theoretical result shows that even in a very low admixture injection pressure, fracturing will occur in surrounding soil.
理论分析发现即使在很小的固化剂注入压力作用下，周围土体也会发生劈裂现象。
The feature parameters extracted from the waveform of the full injection pressure reflecting typical faults are analyzed.
根据某自行火炮喷油压力的波形特点，分析确定了反映典型故障的特征参数。
During core flooding test, the influence of the injected medium on core permeability causes injection pressure to fluctuate.
在岩心流动试验过程中，注入介质对岩心渗透率的影响必然会引起注入压力出现一定幅度的起伏。
The effects caused by injection pressure change in RIM are discussed. Suggestions for determining injection pressure are made.
探讨了注射压力变化引起的RIM工艺中的各种效应。提出了确定注射压力应考虑的事项。
In the function of injection pressure, the mould which has core will produce a little core offset and cause plastics deformation.
具有型芯的模具，在注射压力的作用下，将使型芯产生一定偏移，引起塑件变形。
Commonly used methods to evaluate the injectability included testing injectability coefficient, pushing force and injection pressure.
常用的注射性能评价方法包括测定注射能力系数、推力和注射压力三种。
Pollution in non-target zones can be reduced, the efficiency of profile control can be improved by using rational injection pressure.
合理的注入压力可减少对非目的层的污染，提高调剖措施的有效率。
During the process of water injection production, high injection pressure cut in mudstone should be prevented to reduce casing damage.
油田开采过程中，应防止高压注入水进入泥岩，以预防和减少由于泥岩进水发生蠕变导致套管损坏。
When the close time of the nozzles was set at the end of packing, the injection pressure, clamp force and parts quality were all better.
同时当浇口均设置为保压结束时关闭，成型中的注射压力、锁模力以及制件质量较为理想。
This paper introduces the authors primary research results of the study of the DME spray characteristics under high fuel injection pressure.
介绍了在高压环境下对二甲基醚（DME）喷雾一般特性的试验研究结果，并与柴油的喷雾特性进行了比较。
It's the first time to question extensively the influences of fuel delivery advance Angle and injection pressure on performance of E30 engine.
首次系统地研究了供油提前角、喷嘴启喷压力对E30混合燃料发动机性能的影响。
As the injection pressure subsides, the mold begins to close to perform a coining operation, resulting in a strong, high yield carrier or lens.
随着注射压力的减小，模具开始闭合，进行压印操作，最终生产出高强度、高产量的载体或透镜。
As a result, it was found that injection speed could be increased through varying nozzle port opening width under keeping constant injection pressure.
实验结果表明，在压力恒定的条件下，可通过控制喷嘴开启量大小获得不同的注射充填速度。
The mercury-ejection capillary pressure curve is characterized by integrative fractals and a large range from the highest to lowest injection pressure.
退汞曲线分形特征具有完整性，测量尺度范围从最高注入压力到最低退出压力。
Reasonable injection pressure and rate can improve the development response of gas injection and the recovery factor of carbonate buried hill reservoir.
筛选合理的注入压力、注入速度等参数，为预测注气开发效果、提高碳酸盐岩古潜山油藏开发后期采收率提供了依据。
Due to high water injection pressure, it is difficult to transport the logging cable into water injection WLL by its own weight during well logging process.
在注水井带压测试工艺中，由于注水压力的影响，测井电缆依靠自身质量无法向井下输送，为此开发研制了测井电缆带压下井输送器。
The effect of forming temperature, injection pressure and piston velocity on the filling ability of semi-solid A356 aluminum alloy slurry were investigated.
研究了半固态A356铝合金浆料的成形温度、压射比压和压射冲头速度对半固态A356铝合金流变压铸充填性的影响。
After one year, injection pressure dropped and apparent water injectivity index rose, and interbedded injectivity behavior was improved in the injection wells.
试验一年以后，水井注水压力下降，视吸水指数上升，层间吸水状况得到改善；
Both the shop experiment and field test showed that the wettability alteration agents have the ability to reduce the injection pressure and enhance oil recovery.
室内实验和矿场试验都说明，润湿性反转剂具有降压增注和提高原油采收率的效果。
The injection molding test has been carried out - the test shows that the injection pressure is low, the forming cycle is short and the production efficiency is high.
试验表明热流道注射成型注射压力低、成型周期短、生产效率高。
The larger viscoelasticity of polymer solution, the higher percolation resistance, and the greater of proportion of high injection pressure arising from elastic effect.
聚合物溶液的粘弹性越大，其在地层孔隙中的渗流阻力越大，弹性效应在增高注入压力中所占的份额也越大。
Die casting, the influence factors of filling liquid alloy shape many, including injection pressure, the main injection speed, the fill time and mould temperature, etc.
压铸时，影响合金液充填成型的因素很多，其中主要有压射压力、压射速度、充填时间和模具温度等。
Die casting, the influence factors of filling liquid alloy shape many, including injection pressure, the main injection speed, the fill time and mould temperature, etc.
压铸时，影响合金液充填成型的因素很多，其中主要有压射压力、压射速度、充填时间和模具温度等。
应用推荐