Measuring insulation resistance for circuit.
电路绝缘电阻测量。
Measurementformotor winding insulation resistance.
测量电机绕组绝缘电阻值。
High fracture toughness and insulation resistance.
高断裂强度及绝缘性能。
High insulation resistance, good capacitance stability.
绝缘电阻高，电容量稳定性好。
The insulation resistance of these motors should be kept above 1 megohm.
电动机的绝缘电阻应保持大于1兆欧。
Periodically measure insulation resistance, inspect motor sheath grounding.
定期测量绝缘电阻，检查机壳接地情况。
It introduces the measurement of insulation resistance and its significance.
介绍了绝缘电阻的测试及其意义。
On raining days, the insulation resistance of the generator often drops below 0.5 megohm.
在雨天，发电机的绝缘电阻常常降到0.5兆欧以下。
Inspection installation for antenna of radio console and measuring its insulation resistance.
组装报务台天线安装检查和绝缘测量。
Analysis shows that the main factor of instability of insulation resistance is machining burr.
通过分析，绝缘电阻不稳定的主要原因是机械加工毛刺。
Excess humidity can reduce insulation resistance on PC boards and in test connection insulators.
过高的湿度会降低印制电路板和测试连接绝缘子的绝缘电阻。
A reduction in insulation resistance can, of course, have a serious effect on high impedance measurements.
当然，绝缘电阻的降低会严重影响高阻抗测量工作。
The phenomenon of lower insulation resistance often occurs in the process of telephone cable manufacturing.
绝缘电阻低的现象在生产中时常发生。
The reason that the insulation resistance becomes low for the ZnO arresters base support is briefly analyzed.
简要分析了氧化锌避雷器底座支持小瓷瓶绝缘电阻下降的产生原因，并介绍了一种简便的处理方法。
The procedure for insulation resistance testing consists of preparing, conditioning, and measuring the sample.
绝缘电阻测试的步骤包括样品准备、条件控制和测量样品等。
Insulation resistance is used to describe the isolation performance of high voltage system of electric vehicle.
提出用绝缘电阻描述电动汽车高压电气系统的绝缘性能。
This article makes a thorough theoretical study of the insulation resistance of non-filled plastic telephone cable.
本文对非填充全塑市话电缆的绝缘电阻进行了深入的理论研究。
This diagram shows measuring the insulation resistance between any one pin and all other pins on a multipin connector.
在该图中，我们测量一个多管脚的连接器中某个管脚与其它所有管脚之间的绝缘电阻。
If a PCB has low insulation resistance (ir), it can degrade the performance of the circuits on the board considerably.
如果某块PC B具有低绝缘电阻(IR)，则会大大降低印制板上电路的性能。
Sometimes the insulation resistance of a sample is measured only to determine that it is greater than a specified minimum value.
有时候测量一个样本的绝缘电阻仅仅是为了确认大于规定的一个最小值。
Room test shows that the accuracy of the apparatus is higher than that of the commonly-used insulation resistance testing device.
室内测试结果表明，其精度高于常用的绝缘电阻测试仪表。
Some of these applications may include leakage current of capacitors, reverse diode leakage, or insulation resistance of cables or films.
这类应用可能包括电容器的漏电流、二极管反向漏电、电缆或薄膜的绝缘电阻等。
Low surface insulation resistance (SIR) of a printed circuit board (PCB) can degrade the performance of the circuits on the board considerably.
印制电路板的表面绝缘电阻(SIR)低会大大降低电路板的电路性能。
The testing of insulation resistance, dielectrics voltage-resistance and contact resistance is essential for the connector to reliably operate.
绝缘电阻、介质耐压和接触电阻检验是保证电连接器正常可靠地工作的最基本的常规检验项目。
Very low residue and few causticity, with high-surface insulation resistance value, no need to wash it also can reach the excellent ICT test value.
焊接后残留物少，腐蚀性小，具有极高的表面绝缘阻抗值，无需清洗即可达到极佳的ICT测试性能。
Check whether the insulation resistance and the dielectric strength of the electric devices attached to the panel and equipment body are sufficient.
检查一下控电板和设备体上的那些电器设备，看看他们的绝缘电阻和绝缘强度是否合格。
Some applications, such as testing insulation resistance of cables and printed circuit boards and high-pot testing, may require switching high voltages.
在有些应用中，例如测试电缆和印制板的绝缘电阻及耐压测试，可能需要切换高压信号。
The procedure for insulation resistance testing consists of preparing, conditioning, and measuring the sample. Details may vary, based on specific test methods.
绝缘电阻测试的步骤包括样品准备、条件控制和测量样品等。根据特定的测试方法，具体的步骤可能会有所变化。
The procedure for insulation resistance testing consists of preparing, conditioning, and measuring the sample. Details may vary, based on specific test methods.
绝缘电阻测试的步骤包括样品准备、条件控制和测量样品等。根据特定的测试方法，具体的步骤可能会有所变化。
应用推荐