Other possible reasons include problems with the oil pump, rod and main bearing clearances, camshaft stopping playing, or cam bearings and lifters.
其他可能的原因包括油泵问题、杆和主轴承的空隙、凸轮轴停止工作、或者凸轮的方位和升降。
Starting Motor, Oil Pump Electrical Motor, Armature.
起动电机，油泵电机，电枢。
Two different views show the completed oil pump inlet elbow.
两种不同的意见显示完成油泵入口肘。
After the oil pump motor finishes starting, the pump is loaded.
油泵电机起动完毕后对泵进行加载。
Burning fuels such as coal and oil pump vast amounts of greenhouse gases into the atmosphere.
燃烧煤炭和石油这类化石燃料会产生大量的温室气体。
Light oil pump house is mainly used to convey some volatile and inflammable oil products.
油库轻油泵房主要输送易蒸发、易燃烧的油品，属于爆炸危险场所。
Sintered properties of the oil pump gears and part to part consistency are also reported.
还报告了油泵齿轮烧结后的性能和零件间性能的均一性。
Turn "Light Oil Pump Run" switcher to "ON" position and make sure the ignition burner is lit.
将“轻油泵运行”转换开关转到“运行”，并确认点火燃烧器已点着。
Downhole gas separator is designed to reduce impacts of gas on oil pump and improve pump efficiency.
为了减少气体对泵的影响，提高抽油泵泵效，设计了井下复合式气锚。
The mechanical seal leakage of hot oil pump has always been an important problem for oil refineries.
热油泵机械密封的泄漏一直是炼油厂关注的重要问题。
Press "start" switch, oil pump starts to run, press "stop"switch, oil pump stops running immediately.
按动“启动”开关，油泵开始运转，再按”停止“开关，油泵立即停止运转。
The reason of shut down caused by main oil pump troubles of centrifugal air compressor is introduced.
介绍了离心式空气压缩机多次出现的因主油泵故障而引起的停机事故的原因。
The main reason of compressor shutdown in normal replacing oil pump is analyzed combining with practice.
结合实际分析了正常倒换油泵过程中压缩机停车的主要原因。
Operation test of emergency switching-off device for oil pump and ventilator (bilge pump) in engine room.
机舱风、油（舱底泵）应急切断装置操作试验。
The downhole oil water separation system is comprised of double fluid flow pump, cyclone separator and oil pump.
井下油水分离系统由双液流泵、旋流分离器和原油提升泵三大部分组成。
The oil pump has the important task of delivering an adequate volume of oil around the engine at a suitable pressure.
机油泵一个重要的任务是给发动机提供足够量的、压力适当的机油。
The fixed value of swing type of oil pump rotor is an important target for controlling and inspecting rotors quality.
摆线型机油泵转子的定值是控制和考核其质量的一个重要指标。
External motor and oil pump enable good ventilating and cooling conditions, safety operation and prolonged service life.
由于电机、油泵外置，其通风冷却条件好，运行安全，寿命长。
External motor and oil pump enable good ventilating and cooling conditions, safety operation and prolonged service life.
由于电机、油泵外置，其通风冷却条件好，运行安全，寿命长。
Proper selection of heating furnace, fuels, cycle oil pump, heat medium and control of reactor temperature were discussed.
讨论了热媒加热系统中的加热炉、燃料、循环油泵、载热体和釜温自控的选择原则。
In addition, the camshaft has an eccentric to operate the fuel pump and a gear to drive the ignition distributor and oil pump.
此外，凸轮轴还带动一个驱动燃料泵的偏心轮和一个带动分电器和油泵的齿轮。
Conducting oil pump prime the pump, pump cover, bearing, bracket, shaft, seals, bearings, impeller of eight large component parts.
导热油泵首要由泵体、泵盖、轴承体、支架、主轴、密封、轴承、叶轮八个年夜的零部件组成。
Press the starting button of the oil pump on the operation box beside the Hydraulic Bump Station. Note: only start one oil pump motor.
按位于液压泵站旁操纵箱上的油泵起动按钮，只起动一台油泵电机。
Other possible reasons include problems with the oil pump, rod and main bearing clearances, camshaft end play, or CAM bearings and lifters.
其他可能的原因包括油泵问题，杆和柱轴承之间的空隙，凸轮轴停止工作或者凸轮的方位和升降等。
Flexibility design method of large scale hot oil pump inlet piping is expounded as well as the layout of pipeline, support and hanger.
介绍了大型热油泵入口管系的柔性设计方法、管道的布置方式、支吊架的设置方式。
External heater is used for heating, together with self-designed high-volume oil pump to make frying oil heating cycle faster and evened.
加热采用外置加热器，配用我厂自主设计的大流量油泵，使煎炸油循环加热速度更快，加热更均匀。
Based on the field requests of the multistage oil pump, a measurement and control system is designed, which can realize the multiparameter.
本文基于多级油泵的现场要求，设计了集多参量检测与控制为一体的多级油泵测控系统。
The hydraulic pressure oil pump wears, the seal does not seal. Should repair or the replacement damage hydraulic pressure oil pump and the seal.
液压油泵磨损，密封件不密封。应修复或更换损坏的液压油泵和密封件。
The common ones are "hard interlock" -between oil pump motor and main motor and "flexible interlock" -between oil supply pressure and main motor.
主轴承供油联锁系统常见的有油泵电机与主电机之间的“硬联锁”和供油压力与主电机之间的“软联锁”。
The common ones are "hard interlock" -between oil pump motor and main motor and "flexible interlock" -between oil supply pressure and main motor.
主轴承供油联锁系统常见的有油泵电机与主电机之间的“硬联锁”和供油压力与主电机之间的“软联锁”。
应用推荐