The one-way air outlet valve (6) adopts a spring type one-way air outlet valve.
所说的单向放气阀（6）采用弹簧式单向放气阀。
Product plan: adopt laser sintering hot-extrusion to manufacture the inlet and outlet valve seat of auto engine.
产品方案：项目产品采用激光烧结热挤压高新工艺技术生产汽车发动机进排气阀座。
Therefore, it is suggested that the outlet valve opening of pH metering box and the time of each reclaiming link be adjusted.
为此提出了解决办法——调整酸碱计量箱出口阀开度及阴、阳床再生各步骤时间。
By laser cladding, the sealing face of the in outlet valve parts in methylamine pump in urea production line has been strengthened.
采用激光熔覆技术对尿素生产线上的甲胺泵进排液阀零件密封面进行强化。
The deprivator comprises thermal pour working section, transitional flowing section, inlet valve, outlet valve and dedusting by-pass system.
该热泳脱除器包括热泳工作段，过渡流动段，进口阀门，出口阀门以及清灰旁路系统。
The utility model is composed of a handle, a pull rod, a barrel body, a piston, a bottom plate, an oil inlet valve, an oil outlet valve, etc.
本实用新型由手柄、拉杆、筒体、活塞、底板、进油阀、出油阀、等部件所构成。
Project Background: the inlet and outlet valve seats of auto engine are main components of various auto engines and internal auto manufacturers import the product mostly.
项目建设背景：汽车发动机进排气阀座是各种汽车发动机的主要部件，目前该产品国内汽车生产厂家大部分从国外进口。
Meanwhile, the flap valve can be used to adjust weight, spring tension and the bottom outlet valve flap valve opening size to determine the pressure and open and close time.
同时，可以利用调整阀瓣的自重、弹簧的弹力以及阀瓣的底孔大小来确定阀门的开启压力和启闭时间。
The washbasin design is unusually straight-lined and flat: gentle steps lend the ceramics a subtle modern look which is discretely underlined by the attractively designed ceramic outlet valve.
在洗脸盆设计是不同寻常的直排，平：温和的步骤借给陶瓷一个微妙的现代外观是离散的精美陶瓷出口阀门设计强调。
This positions the relief valve below the first check valve, enabling the zone to drain through the relief valve outlet.
在这种位置，安全阀位于第一止回阀下面，使得这个区能够通过安全阀出口排放。
Prior to servicing any Watts valve, it is mandatory to shut down the water system by closing both the inlet and outlet shutoff valves.
在维修任何美国瓦茨阀门之前，必须先通过关闭进口和出口关闭阀来实现水系统的关闭。
High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.
高粘度泵的出口管路上还应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。
Avoid areas where salt or other corrosive materials are present. Valve protection caps and valve outlet seals should remain on cylinders not connected for use.
避免储存在有盐或其它腐蚀性材料的地方。不使用时，阀门保护帽和阀门排气口密封应保持在钢瓶上。
It should be noted that the outlet check valve cannot be installed backwards or stuck.
应当注意，出口止回阀不能装反或出现卡死现象。
The straight threads of the nut engage with the mating threads of the valve outlet and are tightened to compress the gasket between the two sealing surfaces.
螺母的直螺纹同阀门排气口的配合螺纹咬合在一起并上紧，来压缩在两个密封表面之间的衬垫。
When returning cylinders to the supplier, properly close the cylinder valve, replace and secure any valve outlet seals, and properly install the cylinder cap.
钢瓶返还给供应商时，正确关闭钢瓶阀门，替换并固定阀门排气口密封，正确安装钢瓶帽。
Valve Disadvantages: the valve is prone to leakage around the stem, especially in-board leakage when a vacuum is pulled on the valve outlet.
阀门的缺点：当阀门排气口处是真空时，阀门在阀杆附近容易泄漏，特别是内部泄漏。
When the temperature control knob to set a temperature, hot and cold water mixing valve through proportional control into the outlet, the outlet temperature is always constant.
当温度调节旋钮设定某一温度后，混水阀通过调节进入出水口的冷热水比例，使出水温度始终保持恒定。
For ventilation of pumps the valve should be mounted adjacent to the pump outlet.
对于泵通风阀应安装毗邻泵出口。
A throttle valve must be installed along outlet pipeline when the conditions of work are not clear or stable, this can guarantee operation at the design point.
当工作条件不明或不稳定时，出口管路中必须安装节流阀，以保证泵在设计点运行。
Make sure that any outlet seal is properly tightened to the same torque requirement as the CGA connection for the particular valve outlet.
对于特定的阀门排气口，确保所有排气口密封都按与CGA接头同样的转矩要求正确上紧。
A proper drain line connected to the valve outlet and run to a safe place of disposal must be installed.
必须安装一个适当的排泄管道，连接阀门的出水口，并且流向安全的地方。
When disconnecting cylinders with diaphragm valves, it is most important to double close the valve and to properly install the outlet seal.
当切断钢瓶和隔膜阀的连接时，两次关闭阀门和正确安装排气口密封是最重要的。
When disconnecting cylinders with diaphragm valves, it is most important to double close the valve and to properly install the outlet seal.
当切断钢瓶和隔膜阀的连接时，两次关闭阀门和正确安装排气口密封是最重要的。
应用推荐