The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.
连杆的一端与曲轴的连杆轴颈相连，另一端通过活塞销与活塞相连。
A method of forming a piston pin (10) is included.
还包括一种形成活塞销(10)的方法。
This method can be used to analyse the causes of failure of floating piston pin …
运用该方法可以对浮动式活塞销轴承故障进行分析。
The equation describing the motion of the floating piston pin is deduced in this paper.
本文建立了浮动式活塞销的运动方程。
The connecting rod is attached to the piston by the piston pin.
连杆与活塞的连接是采用活塞销。
This method can be used to analyse the causes of failure of floating piston pin bearings.
运用该方法可以对浮动式活塞销轴承故障进行分析。
The process features of the cold and warm extrusion for the piston pin have been simply compared.
简要分析了活塞销冷、温挤压工艺的特点。
As the output of diesel engines is increased, failures of floating piston pin bearings caused by overheating have often been reported.
随着柴油机强化度的提高，浮动式活塞销轴承因过热而产生的故障屡有所见。
The principle of infrared observation circuit and its application in piston pin electric eddy-current defectoscope is introduced in this paper.
本文介绍红外线监测电路的原理以及在活塞销电涡探伤仪中的应用。
The checkout error of distortion and flexure caused by tapers of crank bore and piston pin eye is analysed. The solution for this problem is put forward.
针对一般采用的几种连杆弯曲和扭曲测量方法，就连杆大小端孔锥度造成的测量误差进行了分析，并提出了解决途径。
It proposes measures of improving piston structure design and adopts the structure of cast aluminum bronze embedded in the hole in the piston pin bushing.
据此提出了活塞结构改进设计措施，采用了在活塞销孔内嵌入铸铝青铜衬套结构。
The members include not only piston and piston pin manufacturers, but also academic institutes, colleges and universities, special machine and assistant material manufacturers.
会员的组成除了有活塞、活塞销生产单位外、还有科研和大专院校、专机和辅料生产单位等。
The results indicate that the main reason causing the failure of the piston pin is fold cracks in inner-surface of the piston pins existing before that the engine is assembled and tested.
结果表明，导致活塞销失效的主要原因是活塞销内表面在发动机装配使用前存在折叠裂纹。
The numerical solution of the equation describing the motion of the floating piston pin is obtained by bringing in the conception of friction force coefficient under slide-roll condition.
引入滚滑状况下的摩擦力系数，从而求得活塞销运动方程的数值解。
This paper introduced a four-body contact model of steel crown-the nodular cast-iron skirt-piston pin-connecting bolt for the steel-crown aluminum-skirt composite piston of locomotive diesel engines.
本文以机车柴油机钢顶铝裙组合活塞为对象，建立组合活塞钢顶铝裙连接螺栓-活塞销的四体接触计算模型。
Our piston-pin product is guaranteed in three ways.
活塞销产品实行“三包”服务；
Our piston-pin product is guaranteed in three ways.
活塞销产品实行“三包”服务；
应用推荐