• The design of the coat-hanger die is of significant importance for the polymer melt distribution across the die and the quality of the final product.

    衣架型模头的设计对于熔体分配的均匀性乃至最终产品的均匀性至关重要。

    youdao

  • Advances in the viscoelastic behavior of polymer melt both home and abroad have been reviewed.

    综述了国内外对聚合物熔体粘弹行为的研究。

    youdao

  • The concept of dynamic viscosity-temperature relationship of polymer melt was firstly proposed.

    首次明确提出聚合物熔体的动态粘温关系概念。

    youdao

  • Coat-hanger die is usually used as the polymer melt distributor of the melt-blown nonwoven system.

    熔喷非织造设备中聚合物熔体分配流道主要采用衣架型模头。

    youdao

  • The equivalent distance method is put forward to determine polymer melt front advancement during injection molding.

    提出一种新的确定注塑成型充模阶段塑料熔体前沿位置的当量距离法;

    youdao

  • The applications of polymer melt gear pump in plastics extrusion and microcellular plastics forming are introduced.

    介绍了熔体齿轮泵在塑料挤出成型及微孔塑料加工中的应用。

    youdao

  • A special apparatus was constructed by modifying capillary rheometer to study polymer melt flow behavior through fiber beds.

    通过改装毛细管流变仪建立了专门的实验装置,研究高温高压下熔体在纤维床层中的流动行为。

    youdao

  • Recent research on energy consumption and morphology evolution during the initial stage of polymer melt compounding is reviewed.

    综述了关于高聚物在熔融混合过程中能量消耗及初始阶段形态演化的研究现状。

    youdao

  • Approaches for the fluorination of aromatic polymers can involve a polymer melt that is contacted with an appropriate fluorination reagent.

    氟化芳香族聚合物的方法包括与合适的氟化反应物接触的聚合物熔体。

    youdao

  • This paper sums the study results on wall slip of polymer melt in shear flow, which leads to the physical meaning of the developed Z-W model.

    总结了聚合物熔体在剪切流场壁面滑移研究的成果,提出了Z W模型的物理概念。

    youdao

  • The innovation scheme for filtration of polymer melt was presented, including spinning pack, polymer melt filter and improvement of TiO2 filter.

    介绍了有关熔体过滤方面的改造方案,包括纺丝组件、熔体过滤器和二氧化钛过滤器的改进。

    youdao

  • The response of the polymer melt behavior of orientation for axial vibration of screw in short pipe extrusion die head was studied by the light scattering technology.

    利用光散射测量方法研究了短圆管挤出模头中聚合物熔体取向行为对螺杆轴向振动的响应。

    youdao

  • Based on the analyses of wall slip mechanism of polymer melt flowing, the effects of wall slip on melt filling flow behavior in micro injection molding were investigated.

    分析了微尺度下熔体壁面滑移机理,研究了微注塑成形中壁面滑移对熔体充模流动行为的影响。

    youdao

  • This paper depicts the principle of polymer melt movement and gas penetration in the gas-assisted injection molding and analyzes the boundary condition of gasmelt interface.

    本文描述了气体辅助注射成型过程中熔体流动和气体穿透的原理,分析了气体和熔体交界处应满足的边界条件。

    youdao

  • The research advances about die swell, the reduction of friction between die wall and polymer melt, wall slip and melt fracture in polymer extrusion are described in the paper.

    对有关挤出胀大、减粘降阻、熔体破裂及壁面滑移的研究进展进行了综述,指出气辅挤出技术是解决以上问题的有效方法。

    youdao

  • The quoted MFR value is the weight of polymer melt flowing through an orifice in specified conditions, so the higher the MFR value, the lower the melt viscosity and the easier the material will flow.

    MF R采用的数值是在一定的条件下通过口模的聚合物熔体的重量,所以MF R越大,熔体粘度越低,而材料的流动性就越好。

    youdao

  • The quoted MFR value is the weight of polymer melt flowing through an orifice in specified conditions, so the higher the MFR value, the lower the melt viscosity and the easier the material will flow.

    MF R采用的数值是在一定的条件下通过口模的聚合物熔体的重量,所以MF R越大,熔体粘度越低,而材料的流动性就越好。

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定