Multisensory devices have already been developed and tested on reinnervated amputees, relaying sensations of contact, pressure, vibration, shear force and temperature.
多重感受装置已经研制出来并在经过神经移植的截肢患者身上测试，转换接触、压力、震动、剪切力和温度的感觉。
The purpose of this paper is to find the distribution laws of the shear force between vertical shaft and surface soil, and to lay a foundation for mechanical model of shaft in soil.
揭示矿山立井井筒与周围表土之间剪切力的分布规律，为正确的立井井筒力学模型建立奠定理论基础。
The codes and specifications of China in steel structure field require that the bearing ability of shear force in panel zone must be sufficient and the inclined stiffener should be applied.
我国现行钢结构设计规范与规程对梁柱节点域的抗剪能力提出了具体的要求，并指出当节点域抗剪能力不足时可设置斜向加劲肋。
In addition to vertical shear force, slab-column connections also have to transfer unbalanced moment due to combined vertical and lateral forces as a result of wind effect or earthquake excitations.
在风荷载或地震荷载等水平荷载及竖向荷载共同作用下，板柱节点除了要传递垂直剪力外，还必须传递较大的不平衡弯矩。
There is no shear force in a straight column exposed to an axial compression.
一个轴心受压的直柱是没有剪力的。
The shear force acting on the sample is controlled by adjusting the flow velocity.
通过调节流速大小来控制作用于样品的剪切力大小。
The maximal shear force reduces as the length of anchorage part of piles increases.
增加桩的锚固段的长度可以降低桩身的最大剪力。
The restoring force model for shear force-shear deformation in SRC joints is studied.
研究SRC节点核心区剪力-剪切变形的恢复力模型。
The formation and characters of elastic shear force and plastic shear force are analyzed.
分析弹性剪切力和塑性剪切力的形成及特征，剖析以往解析分析中存在的问题。
Meat color is positively to marble vein, cooking percentage and shear force value(P<0.05);
肉色与大理石纹、熟肉率、剪切力值呈显著正相关（P<0.05）；
A cutting-edge disc shear force testing equipment was designed, and shear force was tested.
设计了切边圆盘剪剪切力测试装置，并对剪切力进行现场测试。
Abstract: shear force is interrelating with width and thickness of plate and obliquity of knife-edge.
文摘：斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
The main path of ultrasonic sludge disintegration was the mechanical effect of hydraulic shear force.
超声破解污泥的主要作用途径是水力剪切力的机械作用。
The results of previous tests on the slab-column connections subjected to punching shear force are reviewed.
本文回顾了前人的钢筋砼板柱结点冲剪试验结果，分析了其所显示的裂缝开展过程和破坏形式。
It was found that concentration and shear force are two important factors that affect the property of the solution.
结果发现：浓度和剪切作用是影响再生丝素蛋白水溶液性质的两个重要因素。
For the inter story shear force, the distribution curves of calculation ones and test ones are approximately linear.
从层间剪力包络图来看，试验值与有限元计算值都呈现近似直线分布。
A solid, however, no matter how plastic it is, dose not flow unless the net shear force on it exceeds a certain value.
但是，对于一种固体，无论其塑性如何，除非所受剪切力超过了某一限值，否则不会流动。
And the impact of the parameters on shear force was analyzed, which includes overlap, side gap, cutting speeds and so on.
并分析了重叠量、侧向间隙、剪切速度等工艺参数对剪切力的影响。
In the gabled frames, the profiled sheet that is used as the roof and the wall can also resist the shear force in their own plane.
门式刚架中，压型钢板在做屋面维护结构的同时，还承受维护结构平面内的荷载。
Minimum shear force required in the design of frame in frame-wall structure and necessity of story beam in shear wall are discussed.
分析了框剪结构中框架承担的最小地震剪力及框剪结构中剪力墙设楼层梁问题。
The analysis is performed based on structural damage for rare earthquakes and maximum interlayer shear force for frequent earthquakes.
分析中对于罕遇地震采用结构损伤为分析依据，对于多遇地震作用下则以层间最大剪力为依据。
The paper analyzed the affection of the average inter-column shear force and the total number of the discrete columns on the factor of safety.
分析了条柱侧面平均剪力和条柱总数对边坡安全系数的影响。
On the basis of the test of full-scale cruciform specimens under low-reversed cyclic load, its load-bearing capacity under shear force was studied.
在已完成的足尺十字形节点试件拟静力实验基础上，对节点的受剪承载力性能加以研究。
The particle route method is produced for the shear force diagram drawing of multi-span beam based on the geometric principle of the force addition.
基于力的合成的几何法原理，提出了绘制多跨梁剪力图的质点路线法。
Formula for internal resistance ratio under a quick section - load, expressions on sectional flexural torque and shear force when rod bent are given.
给出了截面快速加载下的内阻比计算公式，以及杆件弯曲时截面弯矩、剪力的表达式。
The main reason of the damage of the special-column is the strong shear force ratio, so it's important to control the shear force ratio of the joint.
剪压比过大是异形柱节点发生斜压破坏的根本原因，控制节点剪压比尤其是腹板剪压比具有重要的意义。
The contact problems are non-linear problems, which relate to stress concentration, local boundary nonlinear, no-reversibility of shear force, and so on.
接触问题是非线性问题，涉及到应力集中、局部边界非线性、切向力的不可逆性等一系列非线性问题。
A correlation of the energy of the strong magnetic field to the change in shear force was derived in accordance with the principle of energy transformation.
作者根据能量转换原理，推导了从强磁场能量到剪切力的转换关系式。
The processing conditions can also affect the phase morphology. We find that under the stronger shear force the disperse phase of PA66/PHE blend are smaller.
同时，加工条件也会对相形态产生影响，我们发现在强的剪切作用下，PA66／PHE共混物的分散相尺寸更小。
The processing conditions can also affect the phase morphology. We find that under the stronger shear force the disperse phase of PA66/PHE blend are smaller.
同时，加工条件也会对相形态产生影响，我们发现在强的剪切作用下，PA66／PHE共混物的分散相尺寸更小。
应用推荐