Before soldering, be sure to preheat components.
焊接前零件一定要预热。
Wiring or soldering those would take several lifetimes.
焊接和连接这些晶体管需要好几辈子。
Please follow "Reflow Soldering Conditions" in catalogue.
请遵守产品目录中的回流焊条件。
Soldering could cause numerous of spattered sparks and fused dregs.
焊割作业有大量的火星飞溅和熔渣。
Care must be exercised in attaching the lead wires to the soldering tabs.
在往焊接接线片上焊导线时必须非常小心。
Used with the solder wire together, soldering a stainless steel etc metal.
同锡线一起使用，焊接不锈钢等难以上锡的金属。
You may have to mechanically attach your new wires with tiny loops before soldering.
在焊接之前，你可能需要用一些小胶圈以机械方式把导线固定。
An innocent-looking component or even a bit of soldering can be a disguised antenna.
任何一个看起来很无辜的组件甚至一个焊接点都可能是隐藏的天线。
You'll want to make sure that there is no water in the copper pipe you are soldering.
你先要确认要焊接的铜管里没有水。
Are soldering process control plans up to date and reflecting current processing?
焊接过程控制计划是否是最新的并反映当前的制程？
The third phase relates to the positioning and soldering of the metallic beams system.
第三阶段是关于金属梁系统的定位和焊接。
The purge screw should be in the open position and shielded from direct heat when soldering.
排气螺丝应该位于开启位置，并且在焊接时要有遮盖以免被火源烧到。
Use heat as required, in various degrees, from heat guns, soldering irons, torches and welders.
根据不同的使用温度需要使用加热工具，从热枪，烙铁，打火机和焊工。
You may be looking for funny cat videos and think my favorite soldering tutorials are of no interest.
你可能是要找猫咪的滑稽视频，对我最喜欢的电焊教学片毫无兴趣。
The efficiency of this method of welding, and other devices, such as compared with wave soldering.
这种方法焊接的效率高，不伤及其他器件，与波峰焊相比节能。
It's very wise to keep a soldering iron, a roll of solder and desoldering equipment handy at all times.
身边总是有垂手可得的电烙铁和拆焊设备是十分明智的。
Join pipes using couplings, clamps, screws, bolts, cement or soldering, brazing and welding equipment.
使用联接器，夹子，螺钉，螺栓，水泥或焊接，钎焊和焊接设备连接管件。
Fins are attached to the plates by a mechanical fit, gluing, soldering, brazing, welding, or extrusion.
翅片靠机械配合、粘结、软焊、硬焊、焊接或挤压附着在板上。
The welding quality of the solder joint on the conducting wire connected with the soldering cover and the PCB.
导线在接插件焊杯内的焊点和导线在印制板上的焊点的焊接质量。
Soldering iron should be kept in a suitable distance from vinyl sleeve of capacitor in order to avoid sleeve crack.
电烙铁应与电容器塑胶套管保持适当距离，以防止过热造成塑胶套管破裂。
The capacitors shall not be effected by any radiated heat from the soldered PC board or other components after soldering.
焊接后的电容器不应受到任何已焊接p C板或其他元器件热辐射的影响。
Process modifications such as solder pot finishes for wave soldering equipment to avoid leaching issues are now available.
为避免出现浸析问题，诸如波焊设备焊锡槽终饰工艺的修改目前已经完成。
Therefore, it is a reliable service for your soldering and welding process to provide full responsibility for the support.
因此，有可靠的服务为您的钎焊及焊接加工提供全面负责的支持。
Therefore, it is a reliable service for your soldering and welding process to provide full responsibility for the support.
因此，有可靠的服务为您的钎焊及焊接加工提供全面负责的支持。
应用推荐