Hardware consists of microcomputer, stepping motor control card, stepping motor driver and stepping motor and so on.
硬件由微机、步进电机控制卡、步进电机驱动器和步进电机等器件组成。
Such as "Hardware Pulse Assignor" used by driving stepping motor.
如驱动步进电机用的“硬件脉冲分配器”。
Design a sequence generator for the operation of a stepping motor.
设计一个控制步进电机工作的序列产生器。
In this paper, a set of stepping motor drive system used in stage lighting is presented.
文章介绍了应用于舞台灯光摇头灯中的步进电机控制系统。
The paper puts forward a cylindrical staggered-sheet structure micro linear stepping motor.
提出了一种圆筒型错片结构微型直线步进电机。
In addition, this paper also simply analyzes the control of speed change of the stepping motor.
另外,对步进电机的变速控制也作了简要分析。
The paper discusses the single step response characteristic on five-phase hybrid stepping motor.
本文研究了五相混合式步进电动机的单步响应特性。
The practice shows that the performance of this system outdoes the traditional stepping motor controller.
实践表明,系统性能优于传统的步进电机控制器。
A cogging torque measurement system was proposed, which was composed of stepping motor, torque sensor, etc.
提出了一种由步进电机、转矩传感器等元件组成的齿槽转矩测试系统。
This paper introduces two control methods of the flying cut, with brushless DC motor and with stepping motor.
讨论无刷直流电机、步进电机在旋转飞剪系统中应用时的跟踪控制方案,分析了两种方案的异同。
The stepping motor is extensively used as the executive mechanism in the feed servo system of economical type NC lathe.
在经济型数控车床的进给伺服系统中,广泛地采用步进电机做为执行机构。
The thesis presents the subdivision drive method by analyzing the mathematics models of two-phase hybrid stepping motor.
论文通过分析两相混合式步进电机的数学模型,介绍了两相混合式步进电机的细分控制策略。
This paper introduces the NC system of a flame cutting machine based on the industry personal computer and the stepping motor.
本文开发了基于工控机和步进电机运动控制器的经济型数控火焰切割机系统,介绍了系统的硬件构成和软件开发。
The microcomputer controlled test stand 701 adopts power stepping motor to drive the original operating valve to carry out tests.
此种微机控制701试验台,是采用功率步进电机驱动原操作阀进行试验的。
The design example of a tranquil flow pump control system of the stepping motor shows that the project is feasible and effective.
步进电机驱动的平流泵控制系统设计实例表明,这种方案是行之有效的。
The controller case includes stepping motor, self-coupling voltage regulator, alternating-current contactor, relay and micro-transformer.
控制柜主要包括步进电机、自耦调压器、交流接触器、继电器以及微型互感器等。
This paper introduces a double freedom degree motion control system of satellites antenna based on dual-redundancy hybrid stepping motor.
介绍了一种基于双余度混合式步进电动机的双自由度卫星天线运动控制系统。
It briefly describes the working principle of stepping motor based upon the gate tests at the intake tunnel for Laxiwa hydropower project.
以拉西瓦水电站进水口快速闸门模型试验为例,简要阐述了步进电机的工作原理。
Tuning mechanism consists of diffraction grating, trigger controller and high frequency stepping motor of monolithic microprocessor control.
调谐机构由单片机控制的高频步进电机、衍射光栅、触发控制器组成。
The longitudinal mobile platform with the inspection module in place is actuated by a stepping motor moves along a guide rail intermittently.
检测模块安装在纵向移动平台上,纵向移动平台由步进电机驱动沿导轨做间歇直线运动。
The rotating of the stepping motor, the working procedure of the NC Machine Tools and the movement of the conveyer belt are controlled by PLC.
采用PLC对数控机床的加工工艺流程、步进电机的旋转以及零件输送带的运动进行控制。
It is meaningful to take machining and cost during the calculation of torque, which provide a criterion in the design of hybrid stepping motor.
可见在转矩的计算中考虑加工和成本将给混合步进电机的设计提供一个有意义的判断依据。
The GTO drive source of the power stepping motor is made up of the new-type of switching elements—the Gate turn-off Controlled Rectifier (GTO).
功率步进电机的GTO驱动电源,采用了新型开关元件“可关断可控硅”(简称GTO)。
The stepping motor is a precision electromechanical incremental actuator. It widely USES the digital approach for control of industrial machines.
步进电机是一种进行精确步进运动的机电执行元件,它广泛地用于工业机械的数字控制。
The motion control of stepping motor in the servo system is investigated and a motion control module based on digital signal processor is designed.
介绍有关步进电机的伺服运动控制,设计了基于数字信号处理器的运动控制系统。
The software consists of video and image processing software RS232 communication software and the embedded software for driving the stepping motor.
软件组成系统主要包括视频图像处理、RS232通信和电机驱动的嵌入式程序。
New type electric control big gate valve is introduced, which USES JZ - 7 locomotive brake and it is controlled by microprocessor and stepping motor.
介绍了新型电控大闸采用JZ-7机车制动机,通过微处理器和步进电机实现控制。
The article exploits a special NC system based on DOS, choosing PCL-839 3-axis stepping motor control card, and analyzes the expansibility of the card.
文章采用PCL-839三轴步进电机控制卡开发了一套基于DOS的专用数控系统,并对该控制卡功能的扩展进行了分析。
The article exploits a special NC system based on DOS, choosing PCL-839 3-axis stepping motor control card, and analyzes the expansibility of the card.
文章采用PCL-839三轴步进电机控制卡开发了一套基于DOS的专用数控系统,并对该控制卡功能的扩展进行了分析。
应用推荐