A metal strain gauge on the surface of each membrane senses that deflection and generates a signal that indicates pressure.
在每片硅原子膜的表面有一个金属制压力感应器,能检测压力的大小并发出信号。
In addition to the strain gauge, all the electronics required to handle the signal-processing and communications are embedded within the silicone lens (pictured).
除应变仪之外,所有要求能够应付信号处理及通信的电子设备都被植入硅胶镜片内(见图)。
The result is consistent with the measurement of the strain gauge.
其结果与应变片测量结果一致。
Adopt strain gauge type torque sensor, with high reliability, high accuracy and long life.
采用应变片式扭矩传感器,可靠性高,精度高,寿命长。
The load-strain relationship at crack tip is obtained through electric strain gauge measurement.
用电测法得到了裂尖处的载荷—应变标定关系。
A heat insulation shield ring is used to insulate heat between the strain gauge and the circuit board.
在应变计和电路板之间采用隔热挡圈隔热。
Using strain gauge at roots of the teeth, the contact ratio of gears is measured under different loads.
通过在齿根贴电阻应变计,测量了在不同载荷下螺旋锥齿轮的重合度。
The influence of resistance strain gauge length in strain-ring on measuring sensitivity is analysed as well.
同时分析了应变环中电阻应变计长度对测试灵敏度的影响。
It analyses the measuring principle of dynamic strain gauge and introduces the principle of adjusting balance.
分析了动态应变仪的测量原理和调平衡技术的原理。
The principle of the strain gauge technique for thermal expansion measurement was systematically investigated.
详细地探讨了应变片法测量材料线膨胀系数的原理。
The method of detecting wavelength shift using PZT-strain gauge compounding highly linear fiber grating is also presented.
提出并实现了一种用PZT—应变片组合型高线性度光纤光栅探测反射波长移位的方法。
A strain gauge is a force-sensing element whose resistance changes in proportion to the amount of force applied to the element.
这种张力传感器元件是检测力的元件,其电阻值与作用于其上的力成比例。
Use suitable protection glue to conduct coating protection of strain gauge so as to avoid entering of humidity and erosive gases.
采用合适的保护胶对应变计进行涂覆保护,以防止潮气及腐蚀性气体的进入。
The experimental results prove that the strain gauge techniqueforthermal measurement is a reliable and economic alternate method.
试验结果表明,用应变片法测量材料的线膨胀系数是一种简单可靠且经济实用的替代方法。
Residual stress distribution of FSW has high gradient, which makes the conventional strain gauge hole drilling method unsuitable.
应变片钻孔法是工程中应用最广的残余应力测量方法之一。
A new general prefabricated strain sensor called FBG strain gauge is designed, which can be used as a quadratic transform component.
提出一种适合作为二次变换元件使用的通用型应变传感预制结构——光纤光栅应变片。
The temperature effect on concrete strain gauge was analyzed and the temperature correction method of strain gauge was also presented.
针对应变测试过程中温度变化对应变测试的影响作了深入的探讨,提出了应变计温度影响的修正方法。
The experiment of measuring principle stresses at one point by the strain gauge method is a basic experiment in mechanics of materials.
测量一点的主应力的电测实验是材料力学实验中的基本实验。
Objective To develope a new instrument with a pressure sensitive strain gauge for measuring the pain perception threshold of oral mucosa.
目的研制电阻应变式口腔黏膜压力测痛仪,并对正常年轻人的牙龈黏膜疼痛阈进行测试。
Then, the stress pulses can be automatically collected by computer data acquisition system via strain gauge stuck on the middle of the bar.
在杆的中部粘贴应变片,由计算机数据采集系统自动记录应力脉冲的值。
Based on fundamental physical and chemical concepts, this paper introduces briefly the theories of strain gauge adhesion at home and abroad.
本文从物理、化学的基础概念出发,介绍了国内外一些有关理论。
An overview of the features of strain resistance alloy for foil strain gauge in property, composition, application and process is introduced.
简述箔式电阻应变计用应变电阻合金的性能要求、种类、应用以及工艺特点。
The sensitivity of the accelerometer can be obtained by comparing the output of the strain gauge and the integral of the accelerometer output.
通过比较应变计的输出和加速度计输出的积分,可以计算得出被测加速度计的灵敏度。
Because it has a high working temperature, the high temperature strain gauge is necessary in composing the strain measurement electric-bridge.
由于工作温度较高,所以需采用高温应变片来组成应变测量电桥。
In the discussion of the Ni-base strain gauge pressure sensors, the related work of the research group joined by the authors is also included.
在有关镍基应变计型压力敏感元件的讨论中,包括了作者参加的课题组的有关工作。
The performance of pressure sensor lies on the design of sensitive girder, selection and sticking of strain gauge and design of metrical circuit.
冲击式谷物流量传感器是常用的测产装置。 流量传感器的性能主要取决于敏感梁的设计、应变片的选取粘贴以及测量电路的设计。
Fourth chapter mainly elaboratess the signal conditioning circuit of strain gauge and the supply circuit of strain bridge system's design methods.
第四章主要阐述了应变仪信号测量电路及电桥电源电路的设计方法。
The strain collector gathers strain signals of the strain gauge which are converted to numerical signals and input into the data processing system.
应变采集器采集应变片的应变信号,并转换成数值信号,输入到数据处理系统。
This essay emphasized the implementation of intellectuality and network of the high precision ground strain gauge and presented examples of application.
本文介绍了洞室定点高精度地应变仪网络化的实现过程,并给出了应用实例。
This essay emphasized the implementation of intellectuality and network of the high precision ground strain gauge and presented examples of application.
本文介绍了洞室定点高精度地应变仪网络化的实现过程,并给出了应用实例。
应用推荐