The introduction of OR into SBR and NR enhanced their hardness and tear strength .
纳米累托石的加入可以显著提高SBR和NR的硬度和撕裂强度。
It is mainly used as rubber reinforcement and filler, to improve their elongation, tear strength and resistance to abrasion.
主要用作橡胶制品的补强剂和填充剂，能明显改善橡胶制品的抗拉强度、抗撕裂性和耐磨性。
LDPE (Low Density Polyethylene) : Offers such advantage as tear strength and high chemical resistance. It is also waterproof.
(低密度聚乙烯)：具有以下优良性质：高撕裂强度，高耐化学性，防水性。
It has a better flex cracking resistance than those of natural rubber but a lower tear strength and a higher dynamic modulus.
它比天然橡胶具有较好的抗挠曲开裂性能，但撕裂强度较低，动态模量较高。
LDPE (Low Density Polyethylene) : Offers such advantage as tear strength and high chemical resistance. It is also waterproof.
LDPE(低密度聚乙烯)：具有以下优良性质：高撕裂强度，高耐化学性，防水性。
The results showed that the filling of short fiber evidently improved tear strength, modulus at 10%and Shore A hardness of SFRC.
结果表明，短纤维的加入显著提高了SFRC的撕裂强度、10%定伸应力及邵尔A型硬度；
There lie some correlations among mechanical properties. In this paper, we will take tear strength for example to discuss this correlation.
物理性能参数间存在着相互关系，该文将以撕裂强度为例对其进行探讨。
The silicon and fluorine rubber with high temperature resistance, low compression permanent deformation, and high tear strength properties can meet the water sealing gasket requirements.
采用耐高温、低压缩永久变形、高抗撕裂硅、氟橡胶可以满足该部位需耐高温、耐冷却水的要求。
The results show that the presence of carbon fiber obviously enhances the hardness, heat resistance and oil resistance of the composite, but decreases the tear strength of the composite.
结果表明：炭纤维的加入能提高橡胶的硬度、耐热性及耐油性，但橡胶的扯断强度有所下降。
It was shown that MLPB could improve the interface combination between the organic fillers and the rubber matrix, and could increase the tear strength and the stickiness of the IIR rubbers.
研究表明，MLPB能在一定程度上提高有机填料与橡胶基体之间的界面结合强度；同时，也能有效地提高IIR胶料的自粘性能和撕裂强度等性能指标。
The influence of the level of the pretreated short fibre on tensile strength, tear strength, flex fatigue and conductivity of the acetylene black filled VMQ/EPDM blend vulcanizate was studied.
研究了预处理短纤维用量对乙炔炭黑填充甲基乙烯基硅橡胶（VMQ）／EPDM共混硫化胶拉伸、撕裂、耐屈挠疲劳和导电性能的影响。
Tear strength: it is the force required to tear a paper at a precut edge to a specific length and measured in milli-newton.
撕裂度：把一张事先切一小口的纸，撕开到一定长度所需的力，以毫牛顿计算。
Tear strength: it is the force required to tear a paper at a precut edge to a specific length and measured in milli-newton.
撕裂度：把一张事先切一小口的纸，撕开到一定长度所需的力，以毫牛顿计算。
应用推荐