The transverse deformation of the billet was divided into four areas.
研究发现坯料的横向变形分为四个的区域。
The cyclic pressing with transverse deformation can improve the densification effect of the billet.
带有间隙的循环压制，可以提高坯料的致密化效果。
According to the plate butt welding of A105 steel, the transverse deformation was real-time measured during welding.
通过A105钢的平板对接试验，对焊接过程中焊接横向变形进行实时测量。
The method for identification of plastic state of the disk, as well as the approach to obtaining the secant module and transverse deformation coefficient are presented.
提出了轮盘进入塑性状态的鉴别方法、在塑性状态下求出割线模量和横向变形系数的方法等。
Analyze the effect of the longitudinal and transverse structure difference of honeycomb on the longitudinal and transverse deformation process and destroy type of BAHP.
分析蜂窝结构在纵横方向上的差异性和面板原材料钎焊后的力学性能对钎焊铝蜂窝板纵向和横向侧压变形过程及破坏形式的影响。
This kind of difference in thermal state may result in asymmetric thermal regime in embankment, and underlying soil as well. As a result, possible unevenly transverse deformation may appear.
路基阴阳坡面热状况的差异会导致路基下伏土层温度场的不对称性，由此可能引起路基横向的不均匀变形。
Expansion joint: to meet the deformation of foundation, expansion and construction requirements play, prevent play a change in temperature in transverse crack produces.
伸缩缝：为适应地基变形，管身伸缩及施工要求，防止管身在温度变化时产生横向裂缝。
In the analysis of the stress and deformation under dynamic loading, the inertia force and damping moment should be considered in addition to the transverse shear effect.
在分析动载荷下的应力和变形时，除考虑横向剪切效应外，还须考虑微段的惯性力和阻尼力矩。
The effect of transverse shear deformation is considered and Angle of rotation of surface normal for each layer is different.
这类板的横向剪切变形效应必须予以考虑，因而层板不同层的表面法线的转角是不同的。
The transverse shearing deformation and rotational inertia are taken into consideration in the chosen thick plate strips.
所取厚板条考虑横向剪切变形和转动惯量，并取它的各阶振型为条向连续函数。
The effects played by transverse shear deformation, panel geometric parameters, total number of plies, fiber orientation, and initial geometric imperfections are studied.
讨论了横向剪切变形，曲板几何参数，铺层数，铺展方式和初始几何缺陷等各种参数变化的影响。
In this new method the influence of transverse and squeeze deformation was considered, the basic equations are complacated easily like classical theory.
该方法计入了板的横向剪切变形和挤压变形影响，其基本方程如同经典理论一样简单易解。
General analytic solutions for transverse bending of anisotropic rectangular plate using first order shear deformation theory is obtained at the first time by the complex series method (CSM).
采用复级数方法首次建立了基于一阶剪切变形理论的各向异性矩形板横向弯曲一般解析解。
The deformation of functionally graded truncated conical shell subjected to transverse mechanical load as well as non-uniformly thermal load is studied.
研究了功能梯度材料截顶圆锥壳在横向机械载荷与非均匀热载荷同时作用下的变形问题。
The examples show that the critical load of composite shells of revolution will decrease when considering the transverse shear deformation.
数值算例表明，对于复合材料旋转壳，横向剪切变形使其临界载荷降低；
The effect of diffusion controlled interfacial sliding on the transverse shear deformation of fibrous composites is studied.
研究了扩散控制的界面滑动对纤维复合材料的横向剪切变形行为的影响。
Wind cooling accelerated elimination of heat dissipation, and controlled temperature which made welding transverse contraction deformation and the residual stresses decrease.
气冷的方法，可以使试样散热更快，达到控制温度的目的，同时也可以减小焊接残余应力和焊接横向收缩变形。
The atomic movement of the cantilever beam was motivated by transverse force on one end while another end was fixed, through which its bending deformation image was obtained.
通过一端固定另一端施加横向作用力驱使原子运动，得到纳米单晶铜悬臂梁弯曲的变形图。
The analyses show that the transverse shear deformation effect has a significant influence on the thick reinforced concrete slabs and the concentrated load condition.
分析表明，横向剪切变形对钢筋混凝土厚板及集中荷载的影响很大。
The rear impact roller stretches the weld longitudinally with transverse compressive plastic deformation of the weld, thus reducing the residual deformation and stresses in the bead.
后轮将焊缝金属的纵、横向压缩塑性变形充分碾展，减小了工件的残余变形和应力。
The transverse shear deformation effect is included by use of Mindlin-Reissner first-order shear deformation theory.
分析了计及高阶横向剪切变形的正交各向异性弹性板自由振动的问题。
The flexual deformation of casing in a horizontal hole is caused not only by the uniform transverse load from dead weight, but also by the axial load, and the existence of initial bent if any.
水平井套管柱的挠曲变形，不仅受自重引起的横向均布载荷的影响，而且还受轴向力的影响，同时还可能有初弯曲。
Y - brace has the least effect on the deformation of transverse beam and theY - braced frame has the highest load - carrying capacity.
同时Y形支撑对框架横梁的变形影响最小，极限承载力也最高。
An approach using singular functions is propsed to solve the bending deformation and the transverse free vibration problems of beams in consideration of shearing.
提出一种考虑剪切变形影响时，求解梁的弯曲变形和横向自由振动的奇异函数解法。
This paper compared several mechanical models with transverse shear deformation and put forward a kind of layer model assuming that shear stresses vary parabolically through the plate thickness.
比较了考虑横向剪切变形的几种力学模型，提出了一种新的假定剪应力沿板厚呈抛物线分布的分层模型。
Besides the usual membrane stresses and stress couples the equation also contains additional terms reflecting the influences of transverse shear deformation, rotatory inertia and transverse extrusion.
该方程除了包含通常的薄膜内力项和内矩项外，还反映了横向剪切影响、转动惯性效应和横向挤压影响。
The main advantages are the transverse shear deformation and rotary inertia are considered naturally, and there is no restriction on the thickness of plate and height of stiffener.
主要优越性表现为：结构的旋转惯性、剪切变形等都得到了考虑，且不限制结构的板厚度和加强筋的高度。
The differential salt tectonic deformation is mainly represented by structural differentiation at different levels, and structural zonation and segmentation in transverse and longitudinal sections.
差异变形主要表现为纵向上不同层次变形的差异性以及平面上构造变形的分带性与分段性。
This model is developed based on the one-dimensional SMA constitutive equation and multi-cell model, and considers the influence of transverse shear deformation of the hybrid composite beam.
采用多胞模型、形状记忆合金一维本构关系分析方法，同时考虑横向剪切的影响，建立了层合梁的数学模型。
Through simulation and comparison, the influence laws of feed velocity and different rolling ratio on transverse width deformation and force-energy parameters were opened out.
通过模拟比较，揭示了进给速度和轧制比对双球面环件轧制宽展变形与力能参数的作用规律。
应用推荐