油箱体分成两部分，使用抗腐蚀的薄钢板。
Manufactures from the fuel tank itself in two half-sections, using a corrosion-resistant, thin-steel planting.
本轧机主要用于加工较薄钢板，属于小型轧机。
This hot rolling-mill is a smaller mill mainly used for the processing of thin steel plate.
普通工厂每4秒就生产一张薄钢板，10分钟就能生产150张。
Conventional factories can churn out one steel sheet every four seconds, which amounts to 150 of them in 10 minutes.
高低压开关柜及各种配电箱，采用大量的薄钢板折弯零件。
A lot of thin steel sheet bent parts are applied in high and low-voltage switchgear cabinets and various kinds of power distribution boxes.
结合薄钢板剪力墙实例进行分析，计算结果与实验结果相符。
Using the example of the thin steel-plate sheer wall, the analysis data of RC member is get. the data is consistent with the test results.
为不同规格和载重的冷轧薄钢板木托架结构设计提供理论依据。
The purpose was to provide theoretical basis for structure design of wooden pallet for cold rolled steel of different specifications and load.
提出了一种对冷轧薄钢板厚度公差标准水平进行分析比较的方法。
A method of analysing the gauge tolerance standards of cold-rolled steel sheet was put forward.
采用水浸超声聚焦直入射法对镀锌薄钢板点焊接头进行了质量评价。
The quality of spot welds in galvanized sheet metal was evaluated by using ultrasonic water immersion focusing method.
软化发动机冷却水，防止腐蚀和电镀锌薄钢板，起到高度净化作用。
Softening of the engine cooling water is used to prevent corrosion and corrosion and electro- galvanized sheet metal, and capable of high filtration filter element is produced…
提出了一种冷轧薄钢板常用产品标准厚度公差水平进行分析比较的方法。
The method for analysis and comparison of level of the standard gauge tolerance for normal products of the cold rolled steel sheets is put up.
由镀锌或镀铝锌合金的薄钢板冷弯滚压成型，截面按照相应的国家规范确定。
Galvanized by galvanized or cold-formed alloy steel sheet roll forming, cross-section determined in accordance with the corresponding national norms.
通过实焊试验证明了该焊接工艺及设备对于薄钢板或镀锌钢板拼接的可行性。
The welding experiment proves the possibility of this welding technology and equipment for joining of thin steel sheet or zinc-coated steel sheet.
幕墙的厚度只须满足其主要功能就可以了。许多工业建筑物只用薄钢板作外墙。
Curtain walls do not have to be any thicker than required to serve their principal function. Many industrial buildings are enclosed only with light-gage metal.
主要介绍了薄钢板的划分、产品及生产的概括、国内外薄钢板标准体系的特点。
Introduce the classify, product, the producing situation of sheet, and the characteristic of domestic and overseas standard system.
烘箱由薄钢板构成，工作室与箱体外壳间以玻璃纤维作保温材料、门面镶有密封圈。
The oven is made of thin steel sheets, fiberglass is inserted between the working chamber and outer plate of the oven as thermal insulation, there is a seal ring embedded in the door.
对镀锌生产线上连续运动的薄钢板的横向磁通感应加热过程应用了三维有限元分析。
In this paper the 3 dimensional finite element analysis for transverse flux induction heating (TFIH) of continuously moving thin steel strip for galvanizing line are presented.
试验研究了具有一定形貌及粗糙度的激光毛面薄钢板及同材质普通薄钢板的失稳行为。
The plastic instability behavior of the laser-textured steel sheet with defined surface features is investigated. Comparison is made with the normal sheet taken from the same coil of meatal sheet.
照明配电箱用薄钢板做成无骨架形体，主要部件有壳体、零线排、保护接地排、面板等。
The sheet steel for lighting distribution box is made into frameless shape, the main parts of which are shell, zero line bar, protective earth bar and panel etc.
分析了相关制造工艺对冷轧薄钢板性能的影响，指出不同的汽车部件应采取的性能参数。
Effects of relevant manufacture techniques on cold rolled steel sheet performances are analyzed and the performance parameters which should be adopted for different automobile parts are advanced.
钢托盘用喷涂冷轧钢板或镀锌薄钢板制成，100%环保，可回收再利用，资源不浪费。
Steel pallet is made by power coated cold rolling steel or galvanizes steel. 100% environmental protection, recycle uses again, and resources do not waste.
研究了冷轧薄钢板零件的深拉伸新方法和模具结构，提出了模具主要元件的强度计算方法。
This paper studied the new method of deep drawing of cold rolling steel-metal part and the die structure. And it also proposed the strength calculation method of main die component.
经试验论证，建立了进口冷轧薄钢板洛氏硬度HRB的检测方法，为索赔谈判提供了科学依据。
The test result showed that the HRB test method for imported cold rolling sheet was established and a scientific foundation was provided for claim negotiation.
利用自动测试分析系统(ASAME)测量两种薄钢板的成形极限，得到分布较紧密的成形极限带。
The forming limitation of two sheets were measured by using Automated Strain Analysis and Measurement Environment (ASAME) and the compact forming limit belts were obtained.
本文提出了以低合金钢标准样品代替无锡薄钢板参比样品，利用直读光谱仪测定无锡薄钢板镀铬量的方法。
The method of using the standard sample of low alloy steel instead of tin free steel reference sample by direct reading spectrometry was used to determine chromium coating weight.
采用气相快速甄别实验和电化学方法研究了对高速电镀锡薄钢板(DI材)具有缓蚀作用的四种不同的物质。
Four kinds of corrosion inhibitors for drawn-and-ironed (di) material were studied by means of electrochemical method and rapid laboratory evaluation.
然后阐述了专家系统在薄钢板矫直中的具体应用，并给出了薄钢板矫直专家系统的知识库、数据库和模型库的构成；
Then, its applications in straightening plates are elaborated. Finally, the important significance of its applications in straightening plates in iron and steel industry are discussed.
然后阐述了专家系统在薄钢板矫直中的具体应用，并给出了薄钢板矫直专家系统的知识库、数据库和模型库的构成；
Then, its applications in straightening plates are elaborated. Finally, the important significance of its applications in straightening plates in iron and steel industry are discussed.
应用推荐