The stability of hydrolysis and adhesion strength of PU are not good.
聚氨酯的水解稳定性较差，粘结强度偏低。
The sample was characterized by melt flow rate and adhesion strength to aluminum.
用熔体流动速度和粘结强度表示试样的特征。
High refractive index, high transparency and good adhesion strength for PET film.
具有高折射率、高透明度、对已处理的PET有较佳的附著力。
The adhesion strength and stripping and splitting prevention measure were also discussed.
同时研究了涂料的粘附强度、防裂、防剥落等措施。
The peel and the adhesion strength of various solidification fraction of the ETPB were studied.
本文研究ETPB固化剂加入量对粘接和剥离强度的影响。
The adhesion strength development between PCM and commencement mortar has been studied in this test.
本文研究了聚合物水泥砂浆(PCM)与普通水泥砂浆之间的粘接强度。
Adhesion strength of diamond films on cemented carbide were evaluated by Rockwell indentation tests.
扫描电镜观察表面金刚石形貌，洛氏硬度压痕法评价涂层结合情况。
The diffusion of Ti, c, W of the substrate into the film improved the adhesion strength of the interface.
基体中的元素在薄膜中有明显的扩散，有助于提高界面结合强度。
The matrix of Chinese Medicine Patcher was studied by uniform design and taking adhesion strength as index.
采用均匀设计法，以粘着强度为指标，筛选中药巴布剂基质。
The fracture of the pins was caused by improper assembly flow and lower adhesion strength of the fixing glue.
装配方式不合理，固定胶粘接强度不足和工艺不完善是导致引脚断裂的原因。
The effect of monomer ratio, the kind and concentration of keying agent on adhesion strength is also studied.
研究了单体配比、增粘剂种类、增粘剂用量对剥离强度的影响。
The properties of conversion film, such as corrosion resistance and adhesion strength to different coatings, were studied.
研究了膜层的耐蚀性及其与不同漆膜之间的附着力。
In another embodiment, at least one component exhibits interlayer adhesion strength similar to vinylidene chloride polymers.
在另一实施方案中，至少一个组件表现出与偏二氯乙烯聚合物类似的层间粘合强度。
The effects of depositing temperature on the thickness, adhesion strength and hardness of tin film have been studied in this paper.
研究了沉积温度对膜层的厚度、结合力及硬度的影响。
The product has the advantages of good compatibility, high adhesion strength, high hydrolysis resistance and construction convenience.
本发明产品的优点是：相容性好、粘结强度高、耐水解性高和便于施工。
A series of Aluminium silicate gunning refractories and its properties, such as thermal shock resistance, adhesion strength, were measured.
配制系列硅酸铝质喷补料并检测其抗热震性及喷补附着性能等。
Preparation mechanism of Adhesive for PVC-U piping is described and discussion is made of various factors influencing its adhesion strength.
叙述了PVC-U管材胶粘剂的配制原理，讨论了影响其粘结强度的诸多因素。
The graft latex was a new kind of modified latex with high viscosity, good adhesion strength, good resistance of solvent and flame retardation.
所得接枝胶乳粘度较高、粘结性能较好、耐溶剂性能好，且有较好阻燃性。
Polypropylene is a non-polar high polymer. During the treatment, a polar surface layer is formed which gives rise to a higher adhesion strength.
聚丙烯为非极性的高聚物，只有经过特殊的表面处理使其变为极性表面，才能得到高的粘接强度。
The EVA sole adhesive prepared by the method has the advantages of good comprehensive performance, low price and high adhesion strength to an EVA sole.
本发明方法制备的EVA鞋底粘合剂综合性能好、价格便宜、对EVA鞋底的粘接强度高。
The adhesion strength of hydroxyethyl methyl cellulose modified mortar and ethylene copolymer modified mortar were studied at different curing condition.
研究了羟乙基甲基纤维素和乙烯基共聚物两种聚合物干粉改性砂浆在不同养护条件下的粘结抗拉强度。
The four-point-bending method is a comparatively ideal method to evaluate the adhesion strength Of vapor deposited film to matrix is given in this paper.
本文指出四点弯曲法是定性分析和定量计算气相沉积薄膜与基体结合强度的较理想的方法。
The designer should consolidates the experience, adopt the formula rationally and calculate the internal-power, compressive and adhesion strength accurately.
工程实践中，设计者应当总结经验，对锚筋内力、桩承载力和粘结力采用合理公式并准确计算。
The results show that the interfacial adhesion strength increased noticeably for composites of active aramid fiber but the fracture energy of the interface decreased.
实验结果证明，芳纶表面改性显著提高了其复合材料界面的粘结强度，相反却降低了其界面断裂能。
During the molding and storing process, humidity is the foremost factor affecting the characteristics of HTPB propellant grain and adhesion strength between interfaces.
在成型及贮存过程中，湿度是影响丁羟推进剂药柱性能及各界面的联合粘接强度的首要因素。
The adhesion strength between the dyes covered aluminum foils and PVC can be enhanced significantly by polyester adhesive added modified organic silicon coupling agent.
通过在聚酯胶粘剂中使用改性有机硅偶联剂，可以改善着色铝箔与PVC的粘结性能。
The influence of filler on extensibility, elasticity and adhesion strength of film, and influence of environment temperature on coated film surface dry time are studied.
研究了填料对膜延伸性、弹性、粘结强度的影响，环境温度对涂膜表干时间的影响。
For the sandwich glasses studied in this work, results showed that the matching of the corresponding polar parts of bonded interfaces played primary role in the adhesion strength.
对于本文研究的夹层玻璃，研究发现，粘结界面极性分量匹配性对粘结强度的影响占主要地位。
The contact angles decrease, the roll angles increase, the antifouling performance gets small and the adhesion strength increase with the increment of space of the microstructure.
随着微结构间距的增大，接触角减小，滚动角增大，抗附着性能降低，附着强度增大。
The influence of the incorporation of silane on the polymerization reaction and the adhesion strength was discussed. And the effect factor of the adhesion strength was also depicted.
讨论了有机硅单体的加入对聚合反应、胶粘剂粘接强度的影响，并探讨了影响粘接强度的因素。
应用推荐