The compressive strength also varied with the curing time.
养护时间不同，其抗压强度有明显的差异。
However, the lower temperature, the longer the curing time.
随着温度的进一步降低，环氧树脂的固化更趋缓慢。
The curing time of the mid-coat should be more than 8 hours.
中涂层养护硬化时间约为8小时以上；
Take the average temperature in the curing time as curing temperature.
养护温度取各湿喷桩养护期的平均气温。
To assess the two groups, clinical therapeutic effects and the curing time .
对两组临床疗效及治愈时间进行评定。
The effects of curing time, temperature and bleeding capacity on ice-formation pressure of grout were studied.
研究了养护温度、时间及泌水率对灌浆材料结冰压的影响。
Compared with the chemically cured adhesives, it is convenient for practical use, and its curing time is short.
与化学固化粘合剂相比，其操作使用方便，固化时间短。
It can be quicky cured and resisted high temperature for class H in a short curing time and low evaporation losses.
它耐高温达到H级，固化速度快，贮存周期长，挥发率低。
Automatic pressure compensation, adjust the time and deflated deflated the number of heating temperature, curing time.
可自动压力补偿、调节放气时间和放气次数、加热温度、硫化时间等。
The composition provides improved and reproducible flow during the early stages of molding without compromising curing time.
该组合物在成型的早期阶段提供改善的和可重现的流动而不损害固化时间。
The influence factors on surface curing time of silicone rubber release agent vulcanized at room temperature were analyzed by experiments.
通过实验分析了影响室温硫化硅橡胶脱模剂表面固化时间的各种因素。
User regulator and curing time points at the same time, the user point surge coverage curing point, namely, the principle of user Settings.
用户调压点时间与固化点相同时，用户调压点覆盖固化点，即用户设置优先原则。
Modifying the curing process according to the result of the kinetic study, we are able to reduce the curing time designed by Huang in 2001.
利用反应动力学所得的结果来设计硬化过程所需的温度与时间，可大大缩短黄宏文在2001年时所设计的交联时间。
Overview AJD-I Automatic Temperature Curing time is the struggle against traditional scald the lack of fetal development and production of premium.
概况ajd - I型自动定时温控硫化机是针对传统电烫斗补胎的不足而研制生产的。
The effect of rolling condition and O/P value of phenolic resin on the curing time and flowability of phenolic resin for injection molding was studied.
考察了辊压工艺及酚醛树脂的邻对位比值（O/P）对酚醛注塑料的成型时间及流动性的影响。
Test shows that the curing temperature and curing time are the main factor which affect the whiteness fading and color change of printed white garment.
结果表明，白布在经后整理及成衣印花后，白度下降及颜色变化主要是由后整理及印花中的高温处理温度及时间引起的。
The effects of PPC content, curing agent, curing temperature, curing time and adding carbon black on the mechanical properties of the blends were studied.
研究了PPC的添加量、硫化剂的种类及用量、硫化时间、硫化温度和添加炭黑对共混弹性体的物理力学性能、交联度的影响。
The natural curing time of CPB after hot pressing on the physical and mechanical properties of fast-curing CPB were determined by the hydration of cement.
水泥刨花板卸出压机后的自然养护时间对快速固化水泥刨花板物理力学性能的影响主要取决于板在养护期间水泥的水化情况。
When curing time increasing, cement stone's elasticity deformation restorability in low stress and plasticity deformation capacity in high stress decreased.
随养护时间的延长，水泥石低压应力下的弹性形变恢复能力和高压应力下的塑性形变能力均降低；
The results show that nanometer microwave-absorber can obviously decrease the microwave curing time of modified epoxy adhesive under the same curing condition.
结果表明，在相同固化条件下，纳米微波吸收剂能明显降低改性环氧胶粘剂的微波固化时间。
The results showed that the increasing of curing temperature could improve the compressive strength and shorten the curing time of fly ash based mineral polymer.
结果表明：提高养护温度可以提高粉煤灰基矿物聚合物的抗压强度，缩短养护时间。
The amount of plasticizer, film thickness, curing temperature and curing time effect the release of the DS from the tablet coated with ethylcellulose aqueous dispersion.
结论 ：乙基纤维素水性分散体可作为缓释衣膜材料。增塑剂用量、衣膜厚度、后处理温度、后处理时间等因素均影响药物的释放。
The influence to the strength of glued tailing grain fillings come from the content of cement in it, the mortar density, grain degree and curing time is analyzed in detail.
影响尾砂胶结充填体强度的因素很多。本文就水泥含量、砂浆浓度、尾砂粒级及养护龄期等因素的影响进行了详细的分析…析结果及建议对充填采矿技术人员有一定的参考价值。
On the basis of experiments and analysing the effects of the constant temperature and curing time on the strength of fly-ash, the best curing temperature and time are obtained.
在实验的基础上通过对恒温温度及养护时间对粉煤灰强度影响的分析，得出粉煤灰制品的最佳养护温度和时间。
Formulation, process conditions, curing time and flow behavior of phenolic resin for injection molding with excellent flowability and fast-curing characteristic were described.
介绍了一种高流动性快速固化酚醛注塑料的配方、制备工艺及其成型时间和流动特性。
Objective To study controlling method for curing time of the materials based on isocyanate , and perfect making means and operating rules of transmitting apparatus for the wounded.
目的：研究异氰酸酯基材料固化时间控制方法，以完善基于此材料的伤员固定转运器械的制作方法和操作规程。
Objective To study controlling method for curing time of the materials based on isocyanate , and perfect making means and operating rules of transmitting apparatus for the wounded.
目的：研究异氰酸酯基材料固化时间控制方法，以完善基于此材料的伤员固定转运器械的制作方法和操作规程。
应用推荐