The optimum formulation and processing conditions were determined.
确定了最佳配方和工艺条件。
The influence of processing conditions on the property of phenolic foam was studied.
研究了酚醛泡沫制备工艺中一些参数条件对泡沫体性能的影响。
The etching depth of the circles showed a decreasing trend in the same processing conditions.
比较了相同实验条件下直线轨迹与圆环轨迹的刻蚀深度。
Experience has proved that the design does not meet the actual processing conditions are often failures.
经验证明，不符合实际加工条件的设计往往是失败的。
The processing conditions for preparation of Maize microporous starch by different enzymes were studied.
对酶法水解玉米淀粉制备微孔淀粉的工艺条件进行研究。
Review the design graphics, processing conditions, content changes and development matters with suppliers.
与厂商检讨设计图面、加工条件、改变内容等有关产品开发事宜。
The paper mainly studied the processing conditions of bamboo by hydrogen peroxide alkaline pulping in lab.
对竹片碱性过氧化氢法制浆工艺条件进行了探讨。
When using for more stringent processing conditions, please test in advance, use after verifying repeatedly.
当加工条件比较严格时，请事先进行试验，经过反复验证后再加以使用。
For rotational molded truck fender, raw material, processing conditions and the design of part and mold were studied.
对卡车翼子板滚塑成型原料、工艺条件、制件和模具设计进行了研究。
And studied the processing conditions of making kraft pulp, the influences of different pulp ratio on paper qualities.
本论文着重讨论了用棉秆生产挂面牛皮箱纸板的生产工艺条件。
In injection molding, the residual stress and shrinkage of the product are affected by processing conditions directly.
注塑成型工艺参数对制品的最终残余应力和收缩有着直接的影响。
And gasoline refining was carried by using this catalyst, and the optimum processing conditions were also investigated.
利用自制的催化剂对催化裂解稳定汽油全馏分进行了精制，并研究了其最佳工艺条件。
This paper is mainly concerned about the materials, processing conditions and the application of the edible starch film.
本试验对可食性淀粉膜的制备材料选择、工艺条件及膜的应用进行了研究。
The main ways of bubble prevention are material insurance, dry intensification, strict control of processing conditions.
其主要措施有：把好原料关、加强干燥、严格控制生产工艺条件。
The processing conditions of preparing bio-ethylene with molecular sieve catalyst from ethanol as material were studied.
以分子筛类催化剂对低浓度乙醇脱水制生物乙烯进行了研究。
The processing conditions, formulation and production influencing factors of jelly type coconut yoghurt were probed into.
探讨了凝固型椰子酸奶的工艺条件、配方及生产影响因素。
The raw material and the optimum processing conditions which were suitable for production of HDPE filaments were discussed.
对适合生产聚乙烯单丝的原料和单丝的最佳生产工艺条件进行了探讨。
Processing conditions of effectively separating indium from the leaching solution of a smelting antimony slag were researched.
研究了从冶炼锑渣浸出液中有效地分离铟与锑、铁的工艺条件；
The optimal processing conditions of cultivating lipid yeast by using waste water from soybean product processing was studied.
研究了利用豆制品生产废水培养油脂酵母的适宜工艺条件。
The influences of some factors on the yuba quality were studied and the processing conditions were optimized by uniform design.
利用均匀实验设计方法，探讨了腐竹生产过程中多种因素对腐竹品质的影响并优化了生产工艺条件。
The processing conditions of forming composites such as time, pressure and temperature influence the matrix's impregnating degree.
复合材料的成型条件如成型时间、成型压力、成型温度等影响基体的浸渍程度。
The optimal processing conditions of soybean protein isolation and remarkable problems occurred in production were also presented.
介绍了大豆分离蛋白的最佳生产工艺条件和生产过程中应注意的问题。
The effects of vary compositions of material, catalysts and processing conditions on the spinnability of mullite fibres were investigated.
系统研究了原料配比、催化剂、纺丝助剂等因素对可纺性的影响，初步探讨了反应机理。
Through adjustment on the processing conditions of the alcohol fermentation, will increase the glycerol content in the stillage considerably.
酒精发酵过程中，适当调整它的工艺条件，可将其废液的甘油含量进一步提高。
The synthesis and processing conditions of the bifunctional catalyst for dimethyl ether were studied by using fixed bed reactor in the paper.
本论文采用固定床反应器，对合成二甲醚双功能催化剂及其工艺条件进行了研究。
By analysing the processing conditions and influences of amounts of each masterbatch on film properties, the formulation and process are determined.
通过考察加工条件及各功能母料的用量对薄膜性能的影响，确定了原料配方及薄膜制备工艺。
The process of the injection molding is quite complicated because of the character of the material itself and the complexity of processing conditions.
由于材料本身的特性以及复杂的加工条件，塑料注射成型过程加工过程相当复杂。
The effects of the compositions and processing conditions on the properties and morphological structure of the prepared materials were also discussed.
并就其组成及交联剂用量等条件对材料性能和形态结构的影响作了初步探讨。
However, the property of plastic material itself and the complexity of processing conditions make the process of the injection molding quite complicated.
然而，塑料材料的自有特性和复杂的工艺条件致使注塑成型过程相当复杂。
In accordance with the processing conditions, suitable selection of zeolite and matrix to avoid gasoline overcracking and high coke formation was suggested.
应根据装置加工的具体状况，选择适宜的活性组元及载体，避免汽油的过度裂解和高的生焦率。
应用推荐