Ordinary plasma arc cutting machine power supply.
普通等离子弧切割机的电源。
Nano-metal nickel powder was prepared by plasma arc spraying method.
利用等离子体法制备金属纳米镍粉。
The NC flame and plasma arc cutting is an advanced heating cutting technique.
数控火焰等离子切割是一种先进的热切割技术。
For duplex stainless steel thermal cutting shall be limited to the plasma arc method.
对双相不锈钢进行热切割应该仅限于等离子弧切割方法。
Direct metal forming based on plasma arc welding is a novel rapid prototyping process.
基于等离子弧焊的直接金属成形方法是一种新型的快速成形工艺。
The range which is cleaned up by Plasma arc became small, it tend to format oxidate slag.
等离子弧清理范围变小，易形成氧化物夹渣。
The combustion was tested on plasma arc oven for two kinds of coals used for PCI at Baosteel.
首先进行了单种煤等离子炉燃烧试验，分析了单种煤半焦颗粒的显微形态。
A novel variable polarity plasma arc welding (VPPAW) power supply is introduced in this paper.
介绍了所研制的具有自调整换向功能的大功率变极性等离子弧焊接电源。
The air plasma arc cutting technology is worthy to popularize a new thermal cutting technology.
空气等离子弧切割工艺是值得推广的热切割新技术。
The stability of the AC plasma arc was analyzed on the base of the experiment phenomena in theory .
此外，还根据实验现象从理论上分析了交流等离子电弧的稳定性。
The result of developing SCR power supply for pulse plasma arc welding is introduced in this paper.
本文介绍了可控硅脉冲等离子弧焊电源的研制成果。
A plasma torch's height control system which is based on plasma arc voltage measuring is introduced.
设计了一种基于等离子电弧电压检测的割炬高度控制系统。
The article discussed the feasibility of micro-plasma arc welding Co-Cr alloy for oral cavity repair.
试验研究了钴铬合金口腔修复材料微束等离子弧焊的可行性。
In the finality of this article an experiment study about plasma arc cutting variable-thickness plate is introduced.
本文的最后部分对等离子体弧切割变厚度板材进行实验研究。
Welding equipment includes automatic plasma arc and TIG hardfacing machines. Only a few typical machines are shown here.
焊接设备包括自动等离子弧和TIG 表面硬化机械设备。在此只展示少数典型设备。
This work may be as a useful tool for the understanding of the parameters matching and process optimization in plasma arc welding.
本文的工作对于等离子弧焊接工艺参数的匹配及其过程的优化有重要的指导意义。
The system can not only be used in pulse plasma arc welding, but also can be used in penetration controlling in plasma arc welding.
该系统不仅可以进行脉冲等离子弧焊接，而且可以实现脉冲等离子弧焊接的熔透控制。
To reduce the kerf width and to improve the kerf quality, the experiments of ceramic cutting with water constricted plasma arc are carried out.
为减小切口宽度，提高切口质量，进行了水再压缩等离子弧切割陶瓷实验研究。
The influence of the Angle between laser beam and plasma arc beam on the precision of a deposited layer was analyzed through experimental studies.
通过实验研究分析了激光束与等离子束复合角度对熔积层精度的影响规律。
A non power supply probe was developed to detect the plasma cloud voltage, which consists of plasma arc voltage gradient and plasma sheath voltage.
文中采用无源探针对由等离子弧梯度电压和等离子鞘层电压构成的等离子反翘(等离子云)电压进行检测。
In order to reduce the kerf width and improve the kerf quality, the hydromagnetically confined plasma arc was used to cut engineering ceramic plates.
为减小陶瓷板件切口宽度，提高切口质量，采用水箍和磁场对附加阳极等离子弧进行综合二次约束。
But the argon plasma arc voltage, low enthalpy is not high, cutting ability is limited, and cut the air than the thickness of the cut about 25% lower.
但氩气等离子弧的电压较低，焓值不高，切割能力有限，与空气切割相比其切割的厚度大约会降低25%。
The effects of laser on plasma arc beam, welding depth and width of deposition pool in the hybrid plasma-laser rapid manufacturing is investigated by tests.
通过试验研究了等离子激光复合快速制造中激光对等离子弧柱形貌、熔积成形时的熔深和熔宽等的影响。
The plasma arc forming can also decrease the residual stresses caused in the mechanical processes, which can be of great significance in preventing rebounding.
等离子电弧加热弯曲成形还可以降低机械加工引起的残余应力，有效减少回弹。
Now the plasma arc cutting machine part on gas pressure to control the flow, because when gun aperture, the gas control certain pressure and you control the flow.
现在的等离子弧切割机大多靠气体压力来控制流量，因为当枪体孔径一定时，控制了气体压力也就控制了流量。
Based on just mentioned put forward a basic thought of realizing the automatic control system of keyhole plasma arc welding and designed ensemble control programme.
据此提出了实现等离子弧焊闭环质量控制的基本思想并设计了总体控制方案。
The plasma cloud charge sensor was applied to detect the status of keyhole molten pool during pulsed plasma arc welding, furthermore, the detected signals were studied.
将等离子云传感器应用于脉冲等离子弧焊穿孔熔池小孔状态检测，并对检测信号的波形特征做了深入研究。
This paper introduces the experiment condition and process to carry out hot cutting on silicon nitride ceramics materials with new self-made water-plasma arc equipment.
主要阐述了采用自制新型水介质等离子弧设备对氮化硅陶瓷材料进行加热辅助切削的试验条件及过程。
In this paper, the device of plasma arc restricted by cusp type magnetic field is designed. The machining experiments of plasma arc restricted ny magnetic field is done.
本文设计出尖状磁场约束等离子弧的装置，进行了磁场约束等离子弧的加工实验。
It describes the feature of pulse plasma arc welding and introduces the general design thinking and its composition of SCM control system for the pulse plasma arc welding.
简述了脉冲等离子弧焊接的特点，介绍了该脉冲等离子弧焊接的单片机控制系统总体设计思想及其组成。
应用推荐